欢迎访问ic37.com |
会员登录 免费注册
发布采购

EPM3064ATC100-7N 参数 Datasheet PDF下载

EPM3064ATC100-7N图片预览
型号: EPM3064ATC100-7N
PDF下载: 下载PDF文件 查看货源
内容描述: [EE PLD, 7.5ns, 64-Cell, CMOS, PQFP100, TQFP-100]
分类和应用: 时钟输入元件可编程逻辑
文件页数/大小: 46 页 / 711 K
品牌: INTEL [ INTEL ]
 浏览型号EPM3064ATC100-7N的Datasheet PDF文件第20页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第21页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第22页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第23页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第25页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第26页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第27页浏览型号EPM3064ATC100-7N的Datasheet PDF文件第28页  
MAX 3000A Programmable Logic Device Family Data Sheet  
Table 15. MAX 3000A Device Capacitance  
Note (9)  
Conditions  
Symbol  
Parameter  
Min  
Max  
Unit  
C
C
Input pin capacitance  
I/O pin capacitance  
V
V
= 0 V, f = 1.0 MHz  
8
8
pF  
pF  
IN  
IN  
= 0 V, f = 1.0 MHz  
I/O  
OUT  
Notes to tables:  
(1) See the Operating Requirements for Altera Devices Data Sheet.  
(2) Minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to  
5.75 V for input currents less than 100 mA and periods shorter than 20 ns.  
(3) All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before V  
powered.  
and V  
are  
CCINT  
CCIO  
(4) These values are specified under the recommended operating conditions, as shown in Table 13 on page 23.  
(5) The parameter is measured with 50% of the outputs each sourcing the specified current. The I  
parameter refers  
OH  
to high–level TTL or CMOS output current.  
(6) The parameter is measured with 50% of the outputs each sinking the specified current. The I parameter refers to  
OL  
low–level TTL, PCI, or CMOS output current.  
(7) This value is specified during normal device operation. During power-up, the maximum leakage current is  
300 μA.  
(8) This pull–up exists while devices are programmed in–system and in unprogrammed devices during power–up.  
(9) Capacitance is measured at 25° C and is sample–tested only. The OE1pin (high–voltage pin during programming)  
has a maximum capacitance of 20 pF.  
(10) The POR time for all MAX 3000A devices does not exceed 100 μs. The sufficient V  
voltage level for POR is  
reaches the sufficient POR voltage level.  
CCINT  
3.0 V. The device is fully initialized within the POR time after V  
CCINT  
(11) These devices support in-system programming for –40° to 100° C. For in-system programming support between –40°  
and 0° C, contact Altera Applications.  
Figure 9 shows the typical output drive characteristics of MAX 3000A  
devices.  
24  
Altera Corporation  
 复制成功!