ICS1893BY-10 - Release
Chapter 4 Operating Modes Overview
4.5 100Base-TX Operations
The ICS1893BY-10 100Base-TX mode provides 100Base-TX physical layer (PHY) services as defined in
the ISO/IEC 8802-3 standard. In the 100Base-TX mode, the ICS1893BY-10 is a 100M translator between
a MAC/repeater and the physical transmission medium. As such, the ICS1893BY-10 has two interfaces,
both of which are fully configurable: one to the MAC/repeater and one to the Link Segment. In 100Base-TX
mode, the ICS1893BY-10 provides the following functions:
• Data conversion from both parallel-to-serial and serial-to-parallel formats
• Data encoding/decoding (4B/5B, NRZ/NRZI, and MLT-3)
• Data scrambling/descrambling
• Data transmission/reception over a twisted-pair medium
To accurately transmit and receive data, the ICS1893BY-10 employs DSP-based wave shaping, adaptive
equalization, and baseline wander correction. In addition, in 100Base-TX mode, the ICS1893BY-10
provides a variety of control and status means to assist with Link Segment management. For more
information on 100Base-TX, see Section 6.4, “Functional Block: 100Base-TX TP-PMD Operations”.
4.6 10Base-T Operations
The ICS1893BY-10 10Base-T mode provides 10Base-T physical layer (PHY) services as defined in the
ISO/IEC 8802-3 standard. In the 10Base-T mode, the ICS1893BY-10 is a 10M translator between a
MAC/repeater and the physical transmission medium. As such, the ICS1893BY-10 has two interfaces, both
of which are fully configurable: one to the MAC/repeater and one to the Link Segment. In 10Base-T mode,
the ICS1893BY-10 provides the following functions:
• Data conversion from both parallel-to-serial and serial-to-parallel formats
• Manchester data encoding/decoding
• Data transmission/reception over a twisted-pair medium
In addition, in 10Base-T mode, the ICS1893BY-10 provides a variety of control and status means to assist
with Link Segment management. For more information on 10Base-T, see Section 6.5, “Functional Block:
10Base-T Operations”.
4.7 Half-Duplex and Full-Duplex Operations
The ICS1893BY-10 supports half-duplex and full-duplex operations for both 10Base-T and 100Base-TX
applications. Full-duplex operation allows simultaneous transmission and reception of data, which
effectively doubles the Link Segment throughput to either 20 Mbps (for 10Base-T operations) or 200 Mbps
(for 100Base-TX operations).
As per the ISO/IEC standard, full-duplex operations differ slightly from half-duplex operations. These
differences are necessary, as during full-duplex operations a PHY actively uses both its transmit and
receive data paths simultaneously.
• In 10Base-T full-duplex operations, the ICS1893BY-10 disables its loopback function (that is, it does not
automatically loop back data from its transmitter to its receiver) and disables its SQE Test function.
• In both 10Base-T and 100Base-TX full-duplex operations, the ICS1893BY-10 asserts its CRS signal only
in response to receive activity while its COL signal always remains inactive.
For more information on half-duplex and full-duplex operations, see the following sections:
• Section 7.2, “Register 0: Control Register”
• Section 7.2.8, “Duplex Mode (bit 0.8)”
• Section 7.3, “Register 1: Status Register”
• Section 7.6, “Register 4: Auto-Negotiation Register”
ICS1893BY-10 Rev A 3/24/04
March, 2004
Copyright © 2004, Integrated Circuit Systems, Inc.
All rights reserved.
21
ICSI [ INTEGRATED CIRCUIT SOLUTION INC ]
