欢迎访问ic37.com |
会员登录 免费注册
发布采购

X24645PMG 参数 Datasheet PDF下载

X24645PMG图片预览
型号: X24645PMG
PDF下载: 下载PDF文件 查看货源
内容描述: 先进的2线串行E2PROM带座LockTM保护 [Advanced 2-Wire Serial E2PROM with Block LockTM Protection]
分类和应用: 可编程只读存储器
文件页数/大小: 18 页 / 317 K
品牌: ICMIC [ IC MICROSYSTEMS ]
 浏览型号X24645PMG的Datasheet PDF文件第1页浏览型号X24645PMG的Datasheet PDF文件第3页浏览型号X24645PMG的Datasheet PDF文件第4页浏览型号X24645PMG的Datasheet PDF文件第5页浏览型号X24645PMG的Datasheet PDF文件第6页浏览型号X24645PMG的Datasheet PDF文件第7页浏览型号X24645PMG的Datasheet PDF文件第8页浏览型号X24645PMG的Datasheet PDF文件第9页  
X24645  
ICmic E2PROMs are designed and tested for applications  
requiring extended endurance. Inherent data  
retention is greater than 100 years.  
PIN CONFIGURATIONS  
8-LEAD DIP & SOIC  
V
NC  
CC  
1
2
8
7
PIN DESCRIPTIONS  
Serial Clock (SCL)  
S
1
S
2
X24645  
WP  
SCL  
SDA  
3
4
6
5
The SCL input is used to clock all data into and out of the  
device.  
V
SS  
14-LEAD SOIC  
Serial Data (SDA)  
SDA is a bidirectional pin used to transfer data into and  
out of the device. It is an open drain output and  
NC  
NC  
NC  
NC  
1
2
14  
13  
may be wire-ORed with any number of open drain or  
open collector outputs.  
V
CC  
NC  
3
4
12  
X24645 11  
S
1
An open drain output requires the use of a pull-up  
resistor. For selecting typical values, refer to the Pull-  
WP  
SCL  
SDA  
S
2
5
6
10  
9
V
up resistor selection graph at the end of this data  
sheet.  
SS  
NC  
NC  
7
8
Device Select (S1, S2)  
20-LEAD TSSOP  
The device select inputs (S1, S2) are used to set the first  
and second bits of the 8-bit slave address. This  
NC  
NC  
NC  
1
2
20  
19  
V
CC  
allows up to four X24645 devices to share a common bus.  
These inputs can be static or actively driven. If  
18  
17  
16  
15  
14  
13  
3
4
WP  
NC  
S
1
used statically they must be tied to V  
or V  
as  
appropriate. If actively driven, they must be driven with  
SS  
CC  
NC  
NC  
5
6
7
8
X24645  
CMOS levels (driven to VCC or VSS).  
NC  
NC  
NC  
S
2
SCL  
SDA  
Write Protect (WP)  
The write protect input controls the hardware write  
protect feature. When held LOW, hardware write  
V
SS  
NC  
NC  
NC  
NC  
9
10  
12  
11  
protection is disabled and the X24645 can be written  
normally. When this input is held HIGH, and the WPEN  
2783 ILL F02.4  
bit in the write protect register is set HIGH, write  
protection is enabled, and nonvolatile writes are  
disabled to the selected blocks as well as the write  
protect register itself.  
PIN NAMES  
Symbol  
Description  
S1, S2  
Device Select Inputs  
SDA  
SCL  
WP  
Serial Data  
Serial Clock  
Write Protect  
Ground  
VSS  
VCC  
NC  
Supply Voltage  
No Connect  
2783 FRM T01.1  
2