欢迎访问ic37.com |
会员登录 免费注册
发布采购

56F8036_10 参数 Datasheet PDF下载

56F8036_10图片预览
型号: 56F8036_10
PDF下载: 下载PDF文件 查看货源
内容描述: 16位数字信号控制器 [16-bit Digital Signal Controllers]
分类和应用: 控制器
文件页数/大小: 164 页 / 893 K
品牌: FREESCALE [ Freescale ]
 浏览型号56F8036_10的Datasheet PDF文件第1页浏览型号56F8036_10的Datasheet PDF文件第3页浏览型号56F8036_10的Datasheet PDF文件第4页浏览型号56F8036_10的Datasheet PDF文件第5页浏览型号56F8036_10的Datasheet PDF文件第6页浏览型号56F8036_10的Datasheet PDF文件第7页浏览型号56F8036_10的Datasheet PDF文件第8页浏览型号56F8036_10的Datasheet PDF文件第9页  
Document Revision History  
Version History  
Rev. 0  
Description of Change  
Initial public release.  
Rev. 1  
In Table 10-4, added an entry for flash data retention with less than 100 program/erase  
cycles (minimum 20 years).  
In Table 10-6, changed the device clock speed in STOP mode from 8MHz to 4MHz.  
In Table 10-12, changed the typical relaxation oscillator output frequency in Standby mode  
from 400kHz to 200kHz.  
Changed input propagation delay values in Table 10-21 as follows:  
Old values: 1 μs typical, 2 μs maximum  
New values: 35 ns typical, 45 ns maximum  
Rev. 2  
Rev. 3  
In Table 10-20, changed the maximum ADC internal clock frequency from 8MHz to 5.33MHz.  
Added the following note to the description of the TMS signal in Table 2-3:  
Note: Always tie the TMS pin to VDD through a 2.2K resistor.  
Rev. 4  
Changed the ITCN_BASE address In Table 5-3 (was $00 F060, is $00 F0E0).  
In Figure 5-10, moved the footnote marker (superscript 1) from bit 4 to “RESET”.  
Changed the STANDBY > STOP IDD values in Table 10-6 as follows:  
Typical: was 290μA, is 540μA  
Maximum: was 390μA, is 650μA  
Changed the POWERDOWN IDD values in Table 10-6 as follows:  
Typical: was 190μA, is 440μA  
Maximum: was 250μA, is 550μA  
Changed footnote 1 in Table 10-12 (was “Output frequency after application of 8MHz trim  
value, at 125°C.”, is “Output frequency after application of factory trim”).  
Deleted the text “at 125°C” from Figure 10-5.  
Changed the maximum input offset voltage in Table 10-21 (was +/- 20 mV, is ±35 mV).  
Rev. 5  
Rev. 6  
In Table 2-3, changed VCAP value from 4.7μF to 2.2μF.  
Revised Section 7, Security Features.  
Fixed miscellaneous typos.  
In the table Recommended Operating Conditions, removed the line “XTAL not driven by an  
external clock“ from the characteristic:  
“Oscillator Input Voltage High  
XTAL not driven by an external clock  
XTAL driven by an external clock source”  
In the System Integration Module (SIM chapter), fixed typos.  
Please see http://www.freescale.com for the most current Data Sheet revision.  
56F8036 Data Sheet, Rev. 6  
2
FreescaleSemiconductor  
 复制成功!