欢迎访问ic37.com |
会员登录 免费注册
发布采购

M13S2561616A-5BIG2S 参数 Datasheet PDF下载

M13S2561616A-5BIG2S图片预览
型号: M13S2561616A-5BIG2S
PDF下载: 下载PDF文件 查看货源
内容描述: [DDR DRAM, 16MX16, 0.7ns, CMOS, PBGA60, 8 X 13 MM, 1 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, BGA-60]
分类和应用: 动态存储器双倍数据速率内存集成电路
文件页数/大小: 49 页 / 1245 K
品牌: ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
 浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第13页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第14页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第15页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第16页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第18页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第19页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第20页浏览型号M13S2561616A-5BIG2S的Datasheet PDF文件第21页  
ESMT  
M13S2561616A (2S)  
Operation Temperature Condition -40°C~85°C  
Precharge  
The precharge command is used to precharge or close a bank that has activated. The precharge command is issued when CS ,  
RAS and WE are low and CAS is high at the rising edge of the clock. The precharge command can be used to precharge  
each bank respectively or all banks simultaneously. The bank select addresses (BA0, BA1) are used to define which bank is  
precharged when the command is initiated. For write cycle, tWR(min) must be satisfied until the precharge command can be  
issued. After tRP from the precharge, an active command to the same bank can be initiated.  
Burst Selection for Precharge by bank address bits  
A10/AP  
BA1  
BA0  
Precharge  
Bank A Only  
Bank B Only  
Bank C Only  
Bank D Only  
All Banks  
0
0
0
0
1
0
0
0
1
1
0
1
1
X
X
No Operation & Device Deselect  
The device should be deselected by deactivating the CS signal. In this mode DDR SDRAM should ignore all the control inputs.  
The DDR SDRAMs are put in NOP mode when CS is active and by deactivating RAS , CAS and WE . For both Deselect  
and NOP the device should finish the current operation when this command is issued.  
Bank / Row Active  
The Bank Activation command is issued by holding CAS and WE high with CS and RAS low at the rising edge of the  
clock (CLK). The DDR SDRAM has four independent banks, so Bank Select addresses (BA0, BA1) are required. The Bank  
Activation command must be applied before any Read or Write operation is executed. The Bank Activation command to the first  
Read or Write command must meet or exceed the minimum of RAS to CAS delay time (tRCD min). Once a bank has been  
activated, it must be precharged before another Bank Activation command can be applied to the same bank. The minimum time  
interval between interleaved Bank Activation command (Bank A to Bank B and vice versa) is the Bank to Bank delay time (tRRD  
min).  
Bank Activation Command Cycle ( CAS Latency = 3)  
Tn  
Tn+1  
Tn+2  
0
1
2
3
C L K  
C L K  
B a n k  
A
B a n k  
A
B ank  
A
B a n k  
B
A d d r e s s  
R o w A d d r .  
C o l . A d d r .  
Row. Ad dr.  
R o w A d d r .  
R A S - C A S d e l a y  
(
t
R C D  
)
R A S - R A S d e l a y  
(
t
R R D  
)
W r i t e  
A
B a n k  
A
B a n k  
B
B a n k  
A
N O P  
C o m m a n d  
N O P  
N O P  
w i t h A P  
A c t i v a t e  
A c t i v a t e  
A c t i v a t e  
R O W C y c l e T i m e  
( t R C )  
: D o n ' t C a r e  
Elite Semiconductor Memory Technology Inc.  
Publication Date : Jan. 2015  
Revision : 1.0 17/49