CY7B923
CY7B933
logic and test pattern inputs can be synchronized by sending
a SYNC pattern and allowing the Framer to align the logic to
the bit stream. The flow is as follows:
Receiver Test Mode Description
The CY7B933 Receiver offers two types of test mode opera-
tion, BIST mode and Test mode. In a normal system applica-
tion, the Built-In Self-Test (BIST) mode can be used to check
the functionality of the Transmitter, the Receiver and the link
connecting them. This mode is available with minimal impact
on user system logic, and can be used as part of the normal
system diagnostics. Typical connections and timing are shown
in Figure 7.
1. Assert Test mode for several test clock cycles to establish
normal counter sequence.
2. Assert RF to enable reframing.
3. Input a repeating sequence of bits representing K28.5
(Sync).
4. RDY falling shows the byte boundary established by the
K28.5 input pattern.
BIST Mode
5. Proceed with pattern, voltage and timing tests as is conve-
nient for the test program and tester to be used.
BIST Mode function is as follows:
1. Set BISTEN LOW to enable self-test generation and await
RDY LOW indicating that the initialization code has been
received.
(While in Test mode and in BIST mode with RF HIGH, the Q
,
0-7
RVS, and SC/D outputs reflect various internal logic states and not
the received data.)
2. Monitor RVS and check for any byte time with the pin HIGH
to detect pattern mismatches. RDY will pulse HIGH once
per BIST loop, and can be used by an external counter to
monitor test pattern progress. Q
expected pattern and may be useful for debug purposes.
Test mode is intended to allow logical, DC, and AC testing of
the Receiver without requiring that the tester generate input
data at the bit rate or accommodate the PLL lock, tracking and
frequency range characteristics that are required when the
part operates in its normal mode.
and SC/D will show the
0−7
3. When testing is completed, set BISTEN HIGH and resume
normal function.
X3.230 Codes and Notation Conventions
Note: A specific test of the RVS output may be required to
assure an adequate test. To perform this test, it is only neces-
sary to have the Transmitter send violation (SVS = HIGH) for
a few bytes before beginning the BIST test sequence. Alter-
natively, the Receiver could enter BIST mode after the Trans-
mitter has begun sending BIST loop data, or be removed be-
fore the Transmitter finishes sending BIST loops, each of
which contain several deliberate violations and should cause
RVS to pulse HIGH.
Information to be transmitted over a serial link is encoded eight
bits at a time into a 10-bit Transmission Character and then
sent serially, bit by bit. Information received over a serial link
is collected ten bits at a time, and those Transmission Charac-
ters that are used for data (Data Characters) are decoded into
the correct eight-bit codes. The 10-bit Transmission Code sup-
ports all 256 8-bit combinations. Some of the remaining Trans-
mission Characters (Special Characters) are used for func-
tions other than data transmission.
BIST mode is intended to check the entire function of the
Transmitter, serial link, and Receiver. It augments normal fac-
tory ATE testing and provides the user system with a rigorous
test mechanism to check the link transmission system, without
requiring any significant system overhead.
The primary rationale for use of a Transmission Code is to
improve the transmission characteristics of a serial link. The
encoding defined by the Transmission Code ensures that suf-
ficient transitions are present in the serial bit stream to make
clock recovery possible at the Receiver. Such encoding also
greatly increases the likelihood of detecting any single or mul-
tiple bit errors that may occur during transmission and recep-
tion of information. In addition, some Special Characters of
the Transmission Code selected by Fibre Channel Standard
consist of a distinct and easily recognizable bit pattern (the
Special Character Comma) that assists a Receiver in achiev-
ing word alignment on the incoming bit stream.
When in Bypass mode, the BIST logic will function in the same
way as in the Encoded mode. MODE = HIGH and BISTEN =
LOW causes the Receiver to switch to Encoded mode and begin
checking the decoded received data of the BIST pattern, as if
MODE = LOW. When BISTEN returns to HIGH, the Receiver re-
sumes normal Bypass operation. In Test mode the BIST function
works as in the normal mode.
Test Mode
Notation Conventions
The MODE input pin selects between three receiver functional
modes. When wired to VCC, the Shifter contents bypass the
The documentation for the 8B/10B Transmission Code uses
letter notation for the bits in an 8-bit byte. Fibre Channel Stan-
dard notation uses a bit notation of A, B, C, D, E, F, G, H for
the 8-bit byte for the raw 8-bit data, and the letters a, b, c, d, e,
i, f, g, h, j for encoded 10-bit data. There is a correspondence
between bit A and bit a, B and b, C and c, D and d, E and e, F
and f, G and g, and H and h. Bits i and j are derived, respec-
tively, from (A,B,C,D,E) and (F,G,H).
Decoder and go directly from the Decoder latch to the Q inputs
a−j
of the Output latch. When wired to GND, the outputs are decoded
using the 8B/10B codes shown at the end of this datasheet and
become Q , RVS, and SC/D. The third function is Test mode,
0−7
used for factoryor incomingdevicetest. This modecanbeselected
byleaving the MODE pinopen (internal circuitry forcesthe open pin
to VCC/2).
The bit labeled A in the description of the 8B/10B Transmission
Code corresponds to bit 0 in the numbering scheme of the
FC-2 specification, B corresponds to bit 1, as shown below.
Test mode causes the Receiver to function in its Encoded
mode, but with INB (INB+) as the bit rate Test clock instead of
the Internal PLL generated bit clock. In this mode, transfers
between the Shifter, Decoder register and Output register are
controlled by their normal logic, but with an external bit rate
clock instead of the PLL (the recovered bit clock). Internal
FC-2 bit designation—
HOTLink D/Q designation— 7
8B/10B bit designation—
7
6
6
5
5
4
4
E
3
3
D
2
2
C
1
1
B
0
0
A
H
G F
20
CYPRESS [ CYPRESS ]
