CAT1024, CAT1025
Preliminary Information
Stresses above those listed under “Absolute Maximum Ratings” may
causepermanentdamagetothedevice. Thesearestressratingsonly,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification
is not implied. Exposure to any absolute maximum rating for extended
periods may affect device performance and reliability.
ABSOLUTE MAXIMUM RATINGS
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature....................... –65°C to +150°C
Voltage on any Pin with
Note:
Respect to Ground(1) ............ –2.0V to +VCC +2.0V
(1) The minimum DC input voltage is –0.5V. During transitions,
inputs may undershoot to –2.0V for periods of less than 20 ns.
VCC with Respect to Ground ............... –2.0V to +7.0V
Maximum DC voltage on output pins is V +0.5V, which may
CC
Package Power Dissipation
overshoot to V +2.0V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than
one output shorted at a time.
CC
Capability (TA = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(2) ........................ 100 mA
D.C. OPERATING CHARACTERISTICS
V
CC
= +2.7V to +5.5V and over the recommended temperature conditions unless otherwise specified.
Symbol
Parameter
Test Conditions
VIN = GND to Vcc
VIN = GND to Vcc
Min
-2
Typ
Max
10
Units
µA
ILI
Input Leakage Current
Output Leakage Current
ILO
-10
10
µA
f
SCL = 400kHz
VCC = 5.5V
ICC1
ICC2
ISB
Power Supply Current (Write)
Power Supply Current (Read)
Standby Current
3
1
mA
mA
µA
f
SCL = 400kHz
VCC = 5.5V
Vcc = 5.5V,
40
VIN = GND or Vcc
3
VIL
Input Low Voltage
Input High Voltage
-0.5
0.3 x Vcc
Vcc + 0.5
V
V
3
VIH
0.7 x Vcc
Output Low Voltage
IOL = 3mA
VCC = 2.7V
VOL
VOH
0.4
V
V
(SDA, RESET)
Output High Voltage
(RESET)
IOH = -0.4mA
VCC = 2.7V
Vcc -
0.75
CAT102x-45
(VCC = 5V)
4.50
4.25
3.00
2.85
2.55
4.75
4.50
3.15
3.00
2.70
CAT102x-42
(VCC = 5V)
CAT102x-30
(VCC = 3.3V)
VTH
Reset Threshold
V
CAT102x-28
(VCC = 3.3V)
CAT102x-25
(VCC = 3V)
VRVALID
Reset Output Valid VCC Voltage
Reset Threshold Hysteresis
1.00
15
V
1
VRT
mV
Notes:
1. This parameter is tested initially and after a design or process change that affects the parameter. Not 100% tested.
2. Latch-up protection is provided for stresses up to 100mA on input and output pins from -1V to V + 1V.
CC
3.
V min and V max are reference values only and are not tested.
IL IH
Doc. No. 3008, Rev. G
4
CATALYST [ CATALYST SEMICONDUCTOR ]
