iPEM
2.1 Gb SDRAM-DDR2
Austin Semiconductor, Inc.
AS4DDR232M64PBG
WRITE COMMAND
The WRITE command is used to initiate a burst write access
to an active row. The value on the BA1–BA0 inputs selects
the bank, and the address provided on inputs A0–9 selects
the starting column location. The value on input A10
determines whether or not auto precharge is used. If auto
precharge is selected, the row being accessed will be
precharged at the end of the WRITE burst; if auto precharge
is not selected, the row will remain open for subsequent
accesses.
The time between the WRITE command and the fi rst rising
DQS edge is WL ± tDQSS. Subsequent DQS positive rising
edges are timed, relative to the associated clock edge, as ±
tDQSS. tDQSS is specified with a relatively wide range (25
percent of one clock cycle). All of the WRITE diagrams show
the nominal case, and where the two extreme cases (tDQSS
[MIN] and tDQSS [MAX]) might not be intuitive, they have also
been included. Upon completion of a burst, assuming no
other commands have been initiated, the DQ will remain
High-Z and any additional input data will be ignored.
Input data appearing on the DQ is written to the memory
array subject to the DM input logic level appearing coincident
with the data. If a given DM signal is registered LOW, the
corresponding data will be written to memory; if the DM signal
is registered HIGH, the corresponding data inputs will be
ignored, and a WRITE will not be executed to that byteꢀcolumn
location.
Data for any WRITE burst may be concatenated with a
subsequent WRITE command to provide continuous flow of
input data. The fi rst data element from the new burst is
applied after the last element of a completed burst. The new
WRITE command should be issued x cycles after the first
WRITE command, where x equals BLꢀ2.
DDR2 SDRAM supports concurrent auto precharge options,
as shown in Table 4.
WRITE OPERATION
WRITE bursts are initiated with a WRITE command, as
shown in Figure 12. DDR2 SDRAM uses WL equal to RL
minus one clock cycle [WL = RL - 1ꢁK = AL + (ꢁL - 1ꢁK)].
The starting column and bank addresses are provided with
the WRITE command, and auto precharge is either enabled
or disabled for that access. If auto precharge is enabled, the
row being accessed is precharged at the completion of the
burst. For the generic WRITE commands used in the
following illustrations, auto precharge is disabled.
DDR2 SDRAM does not allow interrupting or truncating any
WRITE burst using BL = 4 operation. Once the BL = 4 WRITE
command is registered, it must be allowed to complete the
entire WRITE burst cycle. However, a WRITE (with auto
precharge disabled) using BL = 8 operation might be
interrupted and truncated ONLY by another WRITE burst as
long as the interruption occurs on a 4-bit boundary, due to
the 4n prefetch architecture of DDR2 SDRAM. WRITE burst
BL = 8 operations may not to be interrupted or truncated with
any command except another WRITE command.
During WRITE bursts, the first valid data-in element will be
registered on the first rising edge of DQS following the WRITE
command, and subsequent data elements will be registered
on successive edges of DQS. The LOW state on DQS
between the WRITE command and the first rising edge is
known as the write preamble; the LOW state on DQS
following the last data-in element is known as the write
postamble.
Data for any WRITE burst may be followed by a subsequent
READ command. The number of clock cycles required to
meet tWTR is either 2 or tWTRꢀtꢁK, whichever is greater.
Data for any WRITE burst may be followed by a subsequent
PREꢁHARGE command. tWT starts at the end of the data
burst, regardless of the data mask condition.
Austin Semiconductor, Inc.
● Austin, Texas ● 512.339.1188 ● www.austinsemiconductor.com
AS4DDR232M64PBG
Rev. 1.3 6/09
18
AUSTIN [ AUSTIN SEMICONDUCTOR ]
