欢迎访问ic37.com |
会员登录 免费注册
发布采购

PI3039 参数 Datasheet PDF下载

PI3039图片预览
型号: PI3039
PDF下载: 下载PDF文件 查看货源
内容描述: 600DPI CIS图像传感器芯片 [600DPI CIS Image Sensor Chip]
分类和应用: 传感器图像传感器
文件页数/大小: 10 页 / 604 K
品牌: AMI [ AMI SEMICONDUCTOR ]
 浏览型号PI3039的Datasheet PDF文件第1页浏览型号PI3039的Datasheet PDF文件第2页浏览型号PI3039的Datasheet PDF文件第4页浏览型号PI3039的Datasheet PDF文件第5页浏览型号PI3039的Datasheet PDF文件第6页浏览型号PI3039的Datasheet PDF文件第7页浏览型号PI3039的Datasheet PDF文件第8页浏览型号PI3039的Datasheet PDF文件第9页  
Video Voltage Output from an  
A4 size CIS module,  
PI620MC-A4.  
(Four Tapped Outputs, for high  
speed application)  
Output voltage non-uniformity  
Vpavg (4)  
1.0  
0.300  
Volts  
Volts  
Using a Red LED Source.  
Using a Yellow-Green LED  
Source. At minimum  
integration time @ 277 µsec  
@ 5MHz clock rate.  
Test circuit used only the  
amplifier of note 4.  
Test circuit used only the  
amplifier in note 4.  
Up (5)  
Ucc  
%
%
± 7.5  
± 7.5  
Chip-to-chip non-uniformity  
Vd (6  
<50  
<20  
mV  
mV  
Test circuit see note 4  
Test circuit see note 4  
)
Dark output voltage  
Dark output non-uniformity  
Ud (6)  
Table 2. Electro-Optical Characteristic  
Notes:  
1) Tint stands for the line scanning rate or the integration time. It is  
determined by the time interval between two start pulses. @the maximum  
clock rate of 6.5 MHz, Tint = 29.5 µsec,  
2) fclk stands for the input clock frequency: Maximum operating frequency is  
6.5 MHz.  
3) There are three types of signal outputs that are called out in the table.  
See under the section entitled, Output Circuits for Converting the  
Video Signal. The referenced section discusses each video output  
circuits. Two are defined for pulsed current, or charge processing, see  
Figure 4A, Virtual Ground Amplifier or see Figure 4C, Signal Current  
to Voltage Converter. The third is voltage output circuit, specified for  
most CIS (contact imaging sensors) application because its lower cost  
and simpler implementation advantages. See Figure 4B, Voltage  
Buffer Amplifier.  
4) Specified for CIS application is a circuit with a buffer amplifier that  
interfaces the video output. See Figure 4B, Voltage Buffer Amplifier.  
This typical video output line is terminated with a commonly used  
standard op-amp circuit. It is located under the section entitled,  
Output Circuits for Converting the Video Signal. The PI227MC-A4 CIS  
module, employing this type of output circuit, was used in the  
measurements. Note a LED light source is an integral part of the  
module.  
5) Up is the uniformity specification. It is measure with the image sensor  
exposed under a uniform light source.  
Up = [(Vpmax-Vpavg)/Vpavg]x100%  
Or [(Vpavg-Vpmin)/Vpavg]x100%, which ever is greater.  
Where Vpavg = å Vpn/Npixels  
Vpn is the nth pixels of sensor chip.  
Npixels is the total number of pixels in sensor chip.  
Vpmax is the maximum pixel output voltage in the light.  
Vpmin is the minimum pixel output voltage in the light.  
Note: In the light means the sensor is exposed to the light.  
PAGE 3 OF 10, PI3039, 12/2/02