欢迎访问ic37.com |
会员登录 免费注册
发布采购

EPM7192SQC160-10 参数 Datasheet PDF下载

EPM7192SQC160-10图片预览
型号: EPM7192SQC160-10
PDF下载: 下载PDF文件 查看货源
内容描述: 可编程逻辑器件系列 [Programmable Logic Device Family]
分类和应用: 可编程逻辑器件输入元件LTE时钟
文件页数/大小: 62 页 / 1087 K
品牌: ALTERA [ ALTERA CORPORATION ]
 浏览型号EPM7192SQC160-10的Datasheet PDF文件第46页浏览型号EPM7192SQC160-10的Datasheet PDF文件第47页浏览型号EPM7192SQC160-10的Datasheet PDF文件第48页浏览型号EPM7192SQC160-10的Datasheet PDF文件第49页浏览型号EPM7192SQC160-10的Datasheet PDF文件第51页浏览型号EPM7192SQC160-10的Datasheet PDF文件第52页浏览型号EPM7192SQC160-10的Datasheet PDF文件第53页浏览型号EPM7192SQC160-10的Datasheet PDF文件第54页  
MAX 7000 Programmable Logic Device Family Data Sheet  
Notes to tables:  
(1) These values are specified under the recommended operating conditions shown in Table 11. See Figure 13 for more  
information on switching waveforms.  
(2) This minimum pulse width for preset and clear applies for both global clear and array controls. The t  
parameter  
LPA  
must be added to this minimum width if the clear or reset signal incorporates the t  
parameter into the signal  
LAD  
path.  
(3) This parameter is a guideline that is sample-tested only and is based on extensive device characterization. This  
parameter applies for both global and array clocking.  
(4) These parameters are measured with a 16-bit loadable, enabled, up/ down counter programmed into each LAB.  
(5) The f  
values represent the highest frequency for pipelined data.  
MAX  
(6) Operating conditions: V  
= 3.3 V ± 10% for commercial and industrial use.  
CCIO  
(7) For EPM7064S-5, EPM7064S-6, EPM7128S-6, EPM7160S-6, EPM7160S-7, EPM7192S-7, and EPM7256S-7 devices,  
these values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these  
devices, add an additional 0.1 ns to the PIA timing value.  
(8) The t  
parameter must be added to the t  
, t  
, t , t , t  
, t  
, and t  
parameters for macrocells  
LPA  
LAD LAC IC EN SEXP ACL  
CPPW  
running in the low-power mode.  
Supply power (P) versus frequency (fMAX in MHz) for MAX 7000 devices  
is calculated with the following equation:  
Power  
Consumption  
P = PINT + PIO = ICCINT × VCC + PIO  
The PIO value, which depends on the device output load characteristics  
and switching frequency, can be calculated using the guidelines given in  
Application Note 74 (Evaluating Power for Altera Devices).  
The ICCINT value, which depends on the switching frequency and the  
application logic, is calculated with the following equation:  
ICCINT  
=
A × MCTON + B × (MCDEV – MCTON) + C × MCUSED × fMAX × togLC  
The parameters in this equation are shown below:  
MCTON  
=
Number of macrocells with the Turbo Bit option turned on,  
as reported in the MAX+PLUS II Report File (.rpt)  
Number of macrocells in the device  
Total number of macrocells in the design, as reported  
in the MAX+PLUS II Report File (.rpt)  
Highest clock frequency to the device  
Average ratio of logic cells toggling at each clock  
(typically 0.125)  
MCDEV  
MCUSED  
=
=
fMAX  
togLC  
=
=
A, B, C  
=
Constants, shown in Table 36  
50  
Altera Corporation  
 复制成功!