EliteMT
M11L416256SA
Notes :
1. Enables on-chip refresh and address counters.
12. Those parameters are referenced to CAS leading
edge in EARLY WRITE cycles and WE leading edge
in LATE WRITE or READ-MODIFY- WRITE cycles.
2. VIH(min) and VIL(max) are reference levels for
measuring timing of input signals. Transition times
are measured between VIH and VIL.
13. During a READ cycle, if OE is low then taken HIGH
before CAS goes high, I/O goes open, if OE is tied
3. In addition to meet the transition rate specification,
all input signals must transit between VIH and VIL in a
monotonic manner.
permanently
low,
a
LATE
WRITE
or
READ-MODIFY-WRITE operation is not possible.
14. An initial pause of 200 μ s is required after power-up
followed by eight RAS refresh cycles (RAS only or
CBR) before proper device operation is assured. The
eight RAS cycle wake-ups should be repeated any
time the tREF refresh requirement is exceeded.
4. Assume that tRCD < tRCD(max). If tRCD is greater than
the maximum recommended value shown in this
table, tRAC will increase by the amount that tRCD
exceeds the value shown.
5. Assume that tRCD ≥ tRCD (max)
15. WRITE command is defined as WE going low.
6. If CAS is low at the falling edge of RAS , data-out
will be maintained from the previous cycle. To initiate
a new cycle and clear the data-out buffer, CAS and
RAS must be pulsed high.
16. LATE WRITE and READ-MODIFY-WRITE cycles must
have both tOFF2 and tOEH met ( OE high during
WRITE cycle) in order to ensure that the output
buffers will be open during the WRITE cycles.
7. Operation within the tRCD limit ensures that tRCD
(max) can be met, tRCD (max) is specified as a
reference point only ; if tRCD is greater than the
specified tRCD (max) limit, access time is controlled
by tCAC.
17. The I/Os open during READ cycles once tOFF1 or tOFF2
occur.
18. Referenced to the earlier CAS falling edge.
19. Referenced to the latter CAS rising edge.
8. Operation within the tRAD limit ensures that tRAD(max)
can be met. tRAD(max) is specified as a reference
point only ; if tRAD is greater than the specified tRAD
(max) limit, access time is controlled by tAA.
20. Output parameter (I/O) is referenced to corresponding
CAS input, IO0~7 by CASL and IO8~15 by
CASH.
21. Last falling CAS edge to first rising CAS edge.
9. Either tRCH or tRRH must be satisfied for a READ
cycle.
22. Last rising CAS edge to next cycle’s last rising
CAS edge.
10. tOFF1(max) defines the time at which the output
achieves the open circuit condition ; it is not a
reference to VOH or VOL.
23. Last rising CAS edge to first falling CAS edge.
24. Each CAS must meet minimum pulse width.
25. Referenced to the latter CAS falling edge.
11. tWCS, tRWD, tAWD and tCWD are restrictive operating
parameters
in
LATE
WRITE
and
≥
26. All IOs controlled by OE , regardless CASL and
CASH.
READ-MODIFY-WRITE cycle only. If tWCS
tWCS(min) , the cycle is an EARLY WRITE cycle and
the data output will remain an open circuit throughout
the entire cycle. If tRWD ≥ tRWD(min) , tAWD ≥ tAWD(min)
and tCWD ≥ tCWD(min) , the cycle is READ-WRITE and
the data output will contain data read from the
selected cell. If neither of the above conditions is
met, the state of I/O (at access time and until CAS
and RAS or OE go back to VIH ) is indeterminate.
OE held high and WE taken low after CAS
goes low result in a LATE WRITE ( OE -controlled)
cycle.
27. Self refresh mode is initiated by performing a CBR
refresh cycle and holding RAS low for the specified
tRASS. Self refresh mode is terminated by rising RAS
high for a minimum time of tRPS.
28. For all of the refresh mode expect the distributed CBR
refresh mode, all rows must be refreshed within the
refresh rate before and after self refresh.
Elite Memory Technology Inc
Publication Date: Aug. 2005
Revision : 1.4
6/16
ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
