C L A S S
MINIATURE SOLID STATE RELAY
226
SPECIFICATIONS CLASS 226
INPUT CHARACTERISTICS
NO
NO
Reverse Polarity Protected:
Input Filtered for transients less than one millisecond.:
OUTPUT CHARACTERISTICS
7 Amps
Rated Load Current: IT (RMS):
W226R & RE-7 Models: 120 VAC,
W226R & RE-8 Models: 240 VAC
W226R & RE-7 Models: 260 VAC,
W226R & RE-8 Models: 380 VAC
W226R & RE-7 Models: 400 VAC,
W226R & RE-8 Models: 700 VAC
50 mA
Line Voltage Range (VAC):
Maximum output voltage (VAC):
Non-Repetitive Peak Voltage VDSM (Blocking Voltage):
Minimum Load Current IT MIN (RMS) to maintain “On”:
Maximum Off State Leakage current ID (RMS):
Maximum RMS On-State Voltage VT (RMS) Maximum
Voltage drop across relay output @ rated current:
Minimum off-state dv/dt:
0.1 mA @ 25˚C, 1.0 mA @ 65˚C
W226R & RE-7 Models: 1.8V, W226R & RE-8 Models: 3.6 V
100V/uSec blocking 4V/uSec commutating
MISCELLANEOUS
SPST-NO
Contact configuration:
2500 VAC
Dielectric Strength VISO (Input-Output Isolation):
Insulation Resistance RISO @ 500VDC:
Operating temperature Range:
Storage temperature Range:
Life:
1010 Ω
-30°C to +80°C
-40°C to +100°C
Greater than 100 million operations
TO-3
Mounting:
0.45 oz. (13 g)
Weight:
PUSH-0N TERMINAL RECEPTACLES
MOLEX
02-06-1103
02-06-1132
WINCHESTER
156-10185
156-10245
FOR 18-22 AWG
FOR 24-30
INPUT (Over Operating Temperature Range) 0UTPUT (Over Operating Temperature Range)
MIN.
DROPOUT
VOLTAGE
PART
NUMBERS
MAX.
PULL-IN
VOLTAGE
MAX.
VOLTAGE
OUTPUT
CURRENT
INPUT
VOLTAGE
NOMINAL
VOLTAGE
FIGURE
PUSH ON TERMINALS
A
1.4 VDC
2.5 VDC
1.4 VDC
2.5 VDC
4.3 VDC
10.3 VDC
4.3 VDC
10.3 VDC
7 AMPS
7 AMPS
7 AMPS
7 AMPS
W226R-7-5A1
5 VDC
12 VDC
5 VDC
12 VDC
260 VAC
260 VAC
380 VAC
380 VAC
120 VAC
120 VAC
240 VAC
240 VAC
A
W226R-7-12A1
A
W226R-8-5A1
A
W226R-8-12A1
PRINTED CIRCUIT TERMINALS
B
1.4 VDC
2.5 VDC
1.4 VDC
2.5 VDC
4.3 VDC
10.3 VDC
4.3 VDC
10.3 VDC
7AMPS
7AMPS
7 AMPS
7AMPS
W226RE-7-5A1
W226RE-7-12A1
W226RE-8-5A1
W226RE-8-12A1
5 VDC
12 VDC
5 VDC
12 VDC
260 VAC
260 VAC
380 VAC
380 VAC
120 VAC
120 VAC
240 VAC
240 VAC
B
B
B
All current ratings are based on use of suitable thermally conductive compound (e.g. silicone grease between the
SSR mounting base and mounting surface of suitable heat sink).
Part Numbers shown also available thru Stocking Distribution.
WEBSITE: www.magnecraft.com - EMAIL:info@magnecraft.com - FAX ON DEMAND 1-800/891-2957 - DOCUMENT 100
PAGE 98
ETC [ ETC ]
