欢迎访问ic37.com |
会员登录 免费注册
发布采购

VG26V17400FJ-5 参数 Datasheet PDF下载

VG26V17400FJ-5图片预览
型号: VG26V17400FJ-5
PDF下载: 下载PDF文件 查看货源
内容描述: 4194304 ×4 - 位CMOS动态RAM [4,194,304 x 4 - Bit CMOS Dynamic RAM]
分类和应用:
文件页数/大小: 25 页 / 210 K
品牌: VML [ VANGUARD INTERNATIONAL SEMICONDUCTOR ]
 浏览型号VG26V17400FJ-5的Datasheet PDF文件第9页浏览型号VG26V17400FJ-5的Datasheet PDF文件第10页浏览型号VG26V17400FJ-5的Datasheet PDF文件第11页浏览型号VG26V17400FJ-5的Datasheet PDF文件第12页浏览型号VG26V17400FJ-5的Datasheet PDF文件第14页浏览型号VG26V17400FJ-5的Datasheet PDF文件第15页浏览型号VG26V17400FJ-5的Datasheet PDF文件第16页浏览型号VG26V17400FJ-5的Datasheet PDF文件第17页  
VG26(V)(S)17400FJ  
4,194,304 x 4 - Bit  
CMOS Dynamic RAM  
VIS  
Notes :  
1. AC measurements assume tT = 5ns.  
2. An initial pause of 100 ms is required after power up, and it followed by a minimum of eight initialization  
cycles (RAS-only refresh cycle or CAS-before-RAS refresh cycle). If the internal refresh counter is  
used, a minimum of eight CAS-before-RAS refresh cycles are required.  
3. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data to  
the device.  
4. All the VCC and VSS pins shall be supplied with the same voltage.  
5. tRAS(min) = tRWD(min) + tRWL(min) + tT in read - modify-write cycle.  
6. tCAS(min) = tCWD(min) + tCWL(min) + tT in read - modify-write cycle.  
7. tASC(min), tRCS(min), tWCS(min) and tRPC are determined by the falling edge of CAS.  
8. tRCD(max) is specified as a reference point only, and tRAC(max) can be met with the tRCD(max) limit.  
Otherwise, tRAC is controlled exclusively by tCAC if tRCD is greater than the specified tRCD(max) limit.  
9. tRAD(max) is specified as a reference point only, and tRAC(max) can be met with the tRAD(max) limit.  
Otherwise, tRAC is controlled exclusively by tAA if tRAD is greater than the specified tRAD(max) limit.  
10. tCRP, tCHR, tRCH, tCPA and tCPW are determined by the rising edge of CAS.  
11. VIH(min) and VIL(max) are reference levels for measuring timing or input signals. Therefore, transition  
time is measured between VIH and VIL.  
12. Assumes that tRCD £ tRCD(max) and tRAD £ tRAD(max). If tRCD or tRAD is greater than the maximum  
recommended value shown in this table, tRAC exceeds the value shown.  
13. Assumes that tRCD ³ tRCD(max) and tRAD £ tRAD(max).  
14. Access time is determined by the maximum among tAA, tCAC, tCPA  
.
15. Assumes that tRCD tRCD(max) and tRAD ³ tRAD(max).  
£
16. Either tRCH or tRRH must be satisfied for a read cycle.  
17. tOFF(max) and tOEZ(max) define the time at which the output achieves the open circuit condition (  
high impedance).  
18. tWCS, tRWD, tCWD, and tAWD are not restrictive operating parameters. They are included in the data  
sheet as electrical characteristics only. If tWCS ³ tWCS(min), the cycle is an early write cycle and the  
data output will remain open circuit (high impedance) throughout the entire cycle. If tRWD ³ tRWD(min),  
tCWD ³ tCWD(min), tAWD ³ tAWD(min), and tCPW ³ tCPW(min), the cycle is a read-modify-write and the  
data output will contain data read from the selected cell. If neither of the above sets of conditions is  
satisfied, the condition of the data output (at access time) is indeterminate.  
19. These parameters are referenced to CAS in an early write cycle and to WE edge in a delayed write or a  
read-modify-write cycle.  
20. tRASP defines RAS pulse width in Fast page mode cycles.  
Document :  
Rev.  
Page13