LM2597, LM2597HV
SNVS119C –MARCH 1998–REVISED APRIL 2013
www.ti.com
PROCEDURE (Adjustable Output Voltage Version)
5. Catch Diode Selection (D1)
EXAMPLE (Adjustable Output Voltage Version)
5. Catch Diode Selection (D1)
A. The catch diode current rating must be at least 1.3 times greater A. Refer to Table 6. Schottky diodes provide the best performance,
than the maximum load current. Also, if the power supply design and in this example a 1A, 40V, 1N5819 Schottky diode would be a
must withstand a continuous output short, the diode should have a good choice. The 1A diode rating is more than adequate and will not
current rating equal to the maximum current limit of the LM2597. The be overstressed even for a shorted output.
most stressful condition for this diode is an overload or shorted
output condition.
B. The reverse voltage rating of the diode should be at least 1.25
times the maximum input voltage.
C. This diode must be fast (short reverse recovery time) and must be
located close to the LM2597 using short leads and short printed
circuit traces. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency, and should be the first choice, especially in low output
voltage applications. Ultra-fast recovery, or High-Efficiency rectifiers
are also a good choice, but some types with an abrupt turn-off
characteristic may cause instability or EMl problems. Ultra-fast
recovery diodes typically have reverse recovery times of 50 ns or
less. Rectifiers such as the 1N4001 series are much too slow and
should not be used.
6. Input Capacitor (CIN
)
6. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the Input capacitor are the input
between the input pin and ground to prevent large voltage transients voltage rating and the RMS current rating. With a nominal input
from appearing at the input. In addition, the RMS current rating of voltage of 28V, an aluminum electrolytic aluminum electrolytic
the input capacitor should be selected to be at least ½ the DC load capacitor with a voltage rating greater than 42V (1.5 × VIN) would be
current. The capacitor manufacturers data sheet must be checked to needed. Since the the next higher capacitor voltage rating is 50V, a
assure that this current rating is not exceeded. The curve shown in 50V capacitor should be used. The capacitor voltage rating of (1.5 ×
Figure 35 shows typical RMS current ratings for several different VIN) is a conservative guideline, and can be modified somewhat if
aluminum electrolytic capacitor values.
desired.
This capacitor should be located close to the IC using short leads The RMS current rating requirement for the input capacitor of a buck
and the voltage rating should be approximately 1.5 times the regulator is approximately ½ the DC load current. In this example,
maximum input voltage.
with a 400 mA load, a capacitor with a RMS current rating of at least
200 mA is needed.
If solid tantalum input capacitors are used, it is recomended that they
be surge current tested by the manufacturer.
The curves shown in Figure 35 can be used to select an appropriate
input capacitor. From the curves, locate the 50V line and note which
capacitor values have RMS current ratings greater than 200 mA. A
47 μF/50V low ESR electrolytic capacitor capacitor is needed.
Use caution when using ceramic capacitors for input bypassing,
because it may cause severe ringing at the VIN pin.
For
additional
information,
see
INPUT
CAPACITOR
For
a through hole design, a 47 μF/50V electrolytic capacitor
inApplication Information section.
(Panasonic HFQ series or Nichicon PL series or equivalent) would
be adequate. Other types or other manufacturers capacitors can be
used provided the RMS ripple current ratings are adequate.
For surface mount designs, solid tantalum capacitors are
recommended. The TPS series available from AVX, and the 593D
series from Sprague are both surge current tested.
To further simplify the buck regulator design procedure, Texas
Instruments is making available computer design software to be
used with the Simple Switcher line of switching regulators.
Table 2. Output Capacitor and Feedforward Capacitor Selection Table
Output
Voltage
(V)
Through Hole Output Capacitor
Surface Mount Output Capacitor
Panasonic
Nichicon PL
Feedforward
AVX TPS
Sprague
Feedforward
HFQ Series
Series
(μF/V)
Series
(μF/V)
595D Series
Capacitor
Capacitor
(μF/V)
(μF/V)
1.2
4
220/25
180/25
82/25
82/25
82/25
82/25
82/50
82/50
220/25
180/25
82/25
0
220/10
100/10
100/10
100/16
100/16
68/20
220/10
120/10
120/10
100/16
100/16
100/20
15/35
0
4.7 nF
4.7 nF
3.3 nF
2.2 nF
1.5 nF
1 nF
4.7 nF
4.7 nF
3.3 nF
2.2 nF
1.5 nF
220 pF
220 pF
6
9
82/25
1 2
1 5
2 4
2 8
82/25
82/25
120/50
120/50
10/35
820 pF
10/35
15/35
16
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM2597 LM2597HV
TI [ TEXAS INSTRUMENTS ]
