欢迎访问ic37.com |
会员登录 免费注册
发布采购

DP83848IVVX 参数 Datasheet PDF下载

DP83848IVVX图片预览
型号: DP83848IVVX
PDF下载: 下载PDF文件 查看货源
内容描述: DP83848I PHYTER工业温度单端口10/100 Mb / s以太网物理层收发器 [DP83848I PHYTER Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver]
分类和应用: 以太网局域网(LAN)标准
文件页数/大小: 86 页 / 788 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号DP83848IVVX的Datasheet PDF文件第44页浏览型号DP83848IVVX的Datasheet PDF文件第45页浏览型号DP83848IVVX的Datasheet PDF文件第46页浏览型号DP83848IVVX的Datasheet PDF文件第47页浏览型号DP83848IVVX的Datasheet PDF文件第49页浏览型号DP83848IVVX的Datasheet PDF文件第50页浏览型号DP83848IVVX的Datasheet PDF文件第51页浏览型号DP83848IVVX的Datasheet PDF文件第52页  
7.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)  
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The content  
changes after the successful auto-negotiation if Next-pages are supported.  
Table 17. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 0x05  
Bit  
Bit Name  
Default  
Description  
15  
NP  
0, RO  
Next Page Indication:  
0 = Link Partner does not desire Next Page Transfer.  
1 = Link Partner desires Next Page Transfer.  
Acknowledge:  
14  
13  
ACK  
RF  
0, RO  
0, RO  
1 = Link Partner acknowledges reception of the ability data word.  
0 = Not acknowledged.  
The Auto-Negotiation state machine will automatically control the  
this bit based on the incoming FLP bursts.  
Remote Fault:  
1 = Remote Fault indicated by Link Partner.  
0 = No Remote Fault indicated by Link Partner.  
RESERVED for Future IEEE use:  
12  
11  
RESERVED  
ASM_DIR  
0, RO  
0, RO  
Write as 0, read as 0.  
ASYMMETRIC PAUSE:  
1 = Asymmetric pause is supported by the Link Partner.  
0 = Asymmetric pause is not supported by the Link Partner.  
PAUSE:  
10  
9
PAUSE  
T4  
0, RO  
0, RO  
0, RO  
0, RO  
0, RO  
0, RO  
1 = Pause function is supported by the Link Partner.  
0 = Pause function is not supported by the Link Partner.  
100BASE-T4 Support:  
1 = 100BASE-T4 is supported by the Link Partner.  
0 = 100BASE-T4 not supported by the Link Partner.  
100BASE-TX Full Duplex Support:  
8
TX_FD  
TX  
1 = 100BASE-TX Full Duplex is supported by the Link Partner.  
0 = 100BASE-TX Full Duplex not supported by the Link Partner.  
100BASE-TX Support:  
7
1 = 100BASE-TX is supported by the Link Partner.  
0 = 100BASE-TX not supported by the Link Partner.  
10BASE-T Full Duplex Support:  
6
10_FD  
10  
1 = 10BASE-T Full Duplex is supported by the Link Partner.  
0 = 10BASE-T Full Duplex not supported by the Link Partner.  
10BASE-T Support:  
5
1 = 10BASE-T is supported by the Link Partner.  
0 = 10BASE-T not supported by the Link Partner.  
4:0  
Selector  
<0 0000>, RO Protocol Selection Bits:  
Link Partner’s binary encoded protocol selector.  
47  
www.national.com