Data Sheet 71M6531D/F-71M6532D/F
FDS 6531/6532 005
The maximum time jitter is 67 µs and is independent of the number of pulses measured. Thus, if the pulse
generator is monitored for one second, the peak jitter is 67 ppm. After 10 seconds, the peak jitter is 6.7 ppm.
The average jitter is always zero. If it is attempted to drive either pulse generator faster than its maximum
rate, it will simply output at its maximum rate without exhibiting any rollover characteristics. The actual
pulse rate, using WSUM as an example, is:
WRATE ⋅WSUM ⋅ FS ⋅ X
,
Hz
RATE =
246
where FS = sampling frequency (2520.6 Hz) and X = Pulse speed factor (as defined in the CECONFIG
register with the PULSE_FAST and PULSE_SLOW bits).
Table 64: CE Pulse Generation Parameters
CE
Name
Default
Description
Address
Kh = VMAX*IMAX*47.1132 / (In_8*WRATE*NACC*X) Wh/pulse. The
default value results in a Kh of 1.0 Wh/pulse when 2520 samples
are taken in each accumulation interval (and VMAX=600,
IMAX = 442 [for 400µΩ shunt], In_8 = 1, X = 6).
Maximum value = 215 -1.
WRATE
827
0x21
Watt pulse generator input (see DIO_PW bit). The output pulse
rate is: APULSEW * FS * 2-32 * WRATE * X * 2-14. This input is buffered
and can be loaded during a computation interval. The change will
take effect at the beginning of the next interval.
APULSEW
APULSER
APULSE2
APULSE3
0
0
0
0x41
0x42
0x43
VAR pulse generator input (see DIO_PV bit). The output pulse rate
is: APULSER * FS*2-32 * WRATE * X * 2-14. This input is buffered and
can be loaded during a computation interval. The change will take
effect at the beginning of the next interval.
Third pulse generator input (see DIO_PV bit). The output pulse
rate is: APULSE2 * FS*2-32 * WRATE * X * 2-14. This input is buffered
and can be loaded during a computation interval. The change will
take effect at the beginning of the next interval.
Fourth pulse generator input (see DIO_PV bit). The output pulse
rate is: APULSE3 * FS*2-32 * WRATE * X * 2-14. This input is buffered
and can be loaded during a computation interval. The change will
take effect at the beginning of the next interval.
0
0x44
0x38
Register for pulse width control of XPULSE and YPULSE. The max-
imum pulse width is (2*PULSEWIDTH+1)*(1/FS). The default value
will generate pulses of 10 ms width at FS = 2520.62 Hz.
PULSE
WIDTH
12
4.3.9 CE Calibration Parameters
Table 65 lists the parameters that are typically entered to effect calibration of meter accuracy.
Table 65: CE Calibration Parameters
CE
Name
Default
Description
Address
These constants control the gain of their respective channels. The
nominal value for each parameter is 214 = 16384. The gain of each
channel is directly proportional to its gain constant. Thus, if the
gain of the IA channel is 1% slow, CAL_IA should be scaled by
1/(1 – 0.01) and the resulting value is 16549.
CAL_IA
CAL_VA
CAL_IB
CAL_VB
16384
16384
16384
16384
0x10
0x11
0x12
0x13
These two constants control the CT phase compensation. No
compensation occurs when PHADJ_X = 0. As PHADJ_X is increased,
more compensation (lag) is introduced. Range: ± 215 – 1. If it is
desired to delay the current by the angle Φ, the equations are:
PHADJ_A
0
0x18
94
© 2005-2010 TERIDIAN Semiconductor Corporation
v1.3
TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
