欢迎访问ic37.com |
会员登录 免费注册
发布采购

71M6531D_10 参数 Datasheet PDF下载

71M6531D_10图片预览
型号: 71M6531D_10
PDF下载: 下载PDF文件 查看货源
内容描述: 电能计量IC [Energy Meter IC]
分类和应用:
文件页数/大小: 120 页 / 1966 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号71M6531D_10的Datasheet PDF文件第83页浏览型号71M6531D_10的Datasheet PDF文件第84页浏览型号71M6531D_10的Datasheet PDF文件第85页浏览型号71M6531D_10的Datasheet PDF文件第86页浏览型号71M6531D_10的Datasheet PDF文件第88页浏览型号71M6531D_10的Datasheet PDF文件第89页浏览型号71M6531D_10的Datasheet PDF文件第90页浏览型号71M6531D_10的Datasheet PDF文件第91页  
FDS 6531/6532 005  
Data Sheet 71M6531D/F-71M6532D/F  
Name  
Location  
Reset Wake  
Dir  
Description  
Selects the trim fuse to be read with the TRIM register:  
TRIMSEL[3:0]  
VERSION[7:0]  
20FD[3:0]  
0
0
R/W  
TRIMSEL[3:0]  
Trim Fuse  
TRIMT[7:0]  
Purpose  
1
Trim for the magnitude of VREF  
2006  
20C8  
R
R
The device version index. This word may be read by the firmware to determine the  
silicon version.  
VERSION[7:0]  
Silicon Version  
0001 0101  
A05  
VREF_CAL  
VREF_DIS  
2004[7]  
2004[3]  
0
0
0
0
R/W Brings VREF to the VREF pad. This feature is disabled when VREF_DIS =1.  
R/W Disables the internal voltage reference.  
Arm the autowake timer. Writing a 1 to this bit arms the autowake timer and presets it  
with the values presently in WAKE_PRD and WAKE_RES. The autowake timer is reset and  
disarmed whenever the IC is in MISSION or BROWNOUT mode. The timer must be  
WAKE_ARM  
20A9[7]  
0
W
armed at least three RTC cycles before the SLEEP or LCD-ONLY mode is commanded.  
R/W Sleep time. Time = WAKE_PRD[2:0]*WAKE_RES. Default = 001. Maximum value is 7.  
R/W Resolution of WAKE timer: 1 = 1 minute, 0 = 2.5 seconds.  
WAKE_PRD  
WAKE_RES  
20A9[2:0]  
20A9[3]  
20B1[0]  
001  
0
0
WD_NROVF_  
FLAG  
R/W This flag is set approximately 1 ms before the watchdog timer overflows. It is cleared  
by writing a 0 or on the falling edge of WAKE.  
WD timer bit. This bit must be accessed with byte operations. Operations possible for  
this bit are: Write 0xFF: Resets the WDT.  
WD_RST  
SFR F8[7]  
2002[2]  
0
0
0
0
W
The WD overflow status bit. This bit is set when the WD timer overflows. It is powered  
by the nonvolatile supply and at bootup will indicate if the part is recovering from a WD  
overflow or a power fault. This bit should be cleared by the MPU on bootup. It is also  
WD_OVF  
R/W  
automatically cleared when RESET is high.  
An 8-bit value has to be written to this address prior to accessing the RTC registers.  
WE  
201F[7:0]  
SFR B2[5]  
0
0
W
When set, this bit protects flash addresses from 0 to BOOT_SIZE*1024 from flash page  
erase.  
WRPROT_BT  
When set, this bit protects flash addresses from CE_LCTN*1024 to the end of memory  
from flash page erase.  
WRPROT_CE  
SFR B2[4]  
0
0
v1.3  
© 2005-2010 TERIDIAN Semiconductor Corporation  
87  
 复制成功!