欢迎访问ic37.com |
会员登录 免费注册
发布采购

HDC1050EVM 参数 Datasheet PDF下载

HDC1050EVM图片预览
型号: HDC1050EVM
PDF下载: 下载PDF文件 查看货源
内容描述: [HDC1050EVM evaluation module (EVM) enables designers to evaluate the operation and performance of the HDC1050 Relative Humidity and Temperature sensor.]
分类和应用:
文件页数/大小: 46 页 / 4206 K
品牌: TAOS [ TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS ]
 浏览型号HDC1050EVM的Datasheet PDF文件第1页浏览型号HDC1050EVM的Datasheet PDF文件第2页浏览型号HDC1050EVM的Datasheet PDF文件第4页浏览型号HDC1050EVM的Datasheet PDF文件第5页浏览型号HDC1050EVM的Datasheet PDF文件第6页浏览型号HDC1050EVM的Datasheet PDF文件第7页浏览型号HDC1050EVM的Datasheet PDF文件第8页浏览型号HDC1050EVM的Datasheet PDF文件第9页  
www.ti.com  
Setup  
2.1 Input/Output Connector Description  
2.1.1  
2.1.2  
2.1.3  
J1 – 5x1 Header  
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and  
Sensor. This connector with its counterpart J2 allows the communication of the two sections through a 4-  
wire cable.  
Pin out:  
J1.1 GND  
J1.2 SDA  
J1.3 SCL  
J1.4 DRDYn (NOTE: this signal is not supported by the HDC1050, and does not need to be  
connected to a host controller)  
J1.5 VDD  
J2 – 5x1 Header  
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and  
Sensor. This connector with its counterpart J1 allows the communication of the two sections through a 5-  
wire cable.  
Pin out:  
J2.1 GND  
J2.2 SDA  
J2.3 SCL  
J2.4 DRDYn (NOTE: this signal is not supported by the HDC1050n and does not need to be  
connected)  
J2.5 VDD  
J3 – USB Type A Connector  
This connector is used for communications with the PC and provides power for the EVM.  
2.2 Hardware Setup  
The HDC1050EVM power is supplied via the USB connector. The LDO (U4) converts the 5V from the  
USB to 3.3V used by the HDC1050 and the MSP430. The EVM may be directly inserted into a USB port  
on a PC or laptop, or may be connected to the latter using the appropriate USB cable.  
The I2C address of the HDC1050 is 1000000xb and is fixed by design.  
The EVM features a Spy-by-Wire interface to the MSP430 that enables custom firmware development and  
debug using Code Composer Studio ©.  
2.3 Software Setup  
2.3.1  
System Requirements  
The Sensing Solutions GUI supports:  
64-bit Windows 7  
64-bit Windows XP  
The current GUI does not support 32-bit Windows operating systems. The host machine is required for  
device configuration and data streaming. The following steps are necessary to prepare the EVM for the  
GUI:  
The GUI and EVM driver must be installed on the host.  
The EVM must be connected to a full speed USB port (USB 1.0 or above).  
3
SNAU181AJune 2015Revised June 2015  
HDC1050EVM User 's Guide  
Submit Documentation Feedback  
Copyright © 2015, Texas Instruments Incorporated