欢迎访问ic37.com |
会员登录 免费注册
发布采购

CC2510F8RSP 参数 Datasheet PDF下载

CC2510F8RSP图片预览
型号: CC2510F8RSP
PDF下载: 下载PDF文件 查看货源
内容描述: 低功耗的SoC (系统级芯片)与MCU,存储器, 2.4 GHz射频收发器和USB控制器 [Low-Power SoC (System-on-Chip) with MCU, Memory, 2.4 GHz RF Transceiver, and USB Controller]
分类和应用: 存储射频控制器
文件页数/大小: 244 页 / 2899 K
品牌: TAOS [ TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS ]
 浏览型号CC2510F8RSP的Datasheet PDF文件第15页浏览型号CC2510F8RSP的Datasheet PDF文件第16页浏览型号CC2510F8RSP的Datasheet PDF文件第17页浏览型号CC2510F8RSP的Datasheet PDF文件第18页浏览型号CC2510F8RSP的Datasheet PDF文件第20页浏览型号CC2510F8RSP的Datasheet PDF文件第21页浏览型号CC2510F8RSP的Datasheet PDF文件第22页浏览型号CC2510F8RSP的Datasheet PDF文件第23页  
C2510Fx / CC2511Fx  
7.8 Frequency Synthesizer Characteristics  
TA = 25 °C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the  
CC2510EM reference designs ([1]).  
Parameter  
Min  
Typ  
Max  
Unit  
Condition/Note  
Programmed frequency  
resolution  
367  
397  
412  
Hz  
24 - 27 MHz crystal.  
Frequency resolution = fXOSC / 216  
Synthesizer frequency  
tolerance  
±40  
ppm  
Given by crystal used. Required accuracy (including  
temperature and aging) depends on frequency band and  
channel bandwidth / spacing.  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
RF carrier phase noise  
PLL turn-on / hop time3  
-77  
-77  
dBc/Hz  
dBc/Hz  
dBc/Hz  
dBc/Hz  
dBc/Hz  
dBc/Hz  
dBc/Hz  
dBc/Hz  
µs  
@ 50 kHz offset from carrier  
@ 100 kHz offset from carrier  
@ 200 kHz offset from carrier  
@ 500 kHz offset from carrier  
@ 1 MHz offset from carrier  
@ 2 MHz offset from carrier  
@ 5 MHz offset from carrier  
@ 10 MHz offset from carrier  
-78  
-88  
-98  
-107  
-116  
-125  
88.4  
85.1  
95.8  
Time from leaving the IDLE state until arriving in the RX,  
FSTXON, or TX state, when not performing calibration.  
Crystal oscillator running.  
PLL RX/TX settling time3  
PLL TX/RX settling time3  
PLL calibration time3  
9.3  
20.7  
694  
9.6  
21.5  
721  
10.4  
23.3  
Settling time for the 1·IF frequency step from RX to TX  
Settling time for the 1·IF frequency step from TX to RX  
µs  
µs  
µs  
780.8  
Calibration can be initiated manually or automatically  
before entering or after leaving RX/TX.  
Table 16: Frequency Synthesizer Parameters  
7.9 Analog Temperature Sensor  
TA= 25 °C, VDD = 3.0V if nothing else stated. All measurement results are obtained using the  
CC2510EM reference designs ([1]).  
Parameter  
Min  
Typ  
Max  
Unit  
Condition/Note  
0.654  
0.750  
0.848  
0.946  
2.43  
0
V
V
V
V
Output voltage at -40 °C  
Output voltage at 0 °C  
Output voltage at +40 °C  
Output voltage at +80 °C  
Temperature coefficient  
mV/°C Fitted from -20 °C to +80 °C  
Error in calculated  
temperature, calibrated  
-2 *  
2 *  
°C  
From -20°C to +80°C when using 2.43 mV / °C, after 1-point  
calibration at room temperature  
* The indicated minimum and maximum error with 1-point  
calibration is based on measured values for typical process  
parameters  
Current consumption  
0.3  
mA  
increase when enabled  
Table 17: Analog Temperature Sensor Parameters  
3
Min figures are given using fXOSC = 27 MHz. Typ figures are given using fXOSC = 26 MHz, and Max  
figures are given using fXOSC = 24 MHz.  
SWRS055D  
Page 19 of 243