欢迎访问ic37.com |
会员登录 免费注册
发布采购

STM32F103RCY7XXX 参数 Datasheet PDF下载

STM32F103RCY7XXX图片预览
型号: STM32F103RCY7XXX
PDF下载: 下载PDF文件 查看货源
内容描述: 高密度高性能线的基于ARM的32位MCU,具有256至512KB闪存, USB , CAN ,11个定时器, 3的ADC ,13个通信接口 [High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces]
分类和应用: 闪存通信
文件页数/大小: 123 页 / 1691 K
品牌: STMICROELECTRONICS [ STMICROELECTRONICS ]
 浏览型号STM32F103RCY7XXX的Datasheet PDF文件第40页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第41页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第42页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第43页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第45页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第46页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第47页浏览型号STM32F103RCY7XXX的Datasheet PDF文件第48页  
Electrical characteristics
STM32F103xC, STM32F103xD, STM32F103xE
5.3.4
Embedded reference voltage
The parameters given in
are derived from tests performed under ambient
temperature and V
DD
supply voltage conditions summarized in
Table 13.
Symbol
V
REFINT
Embedded internal reference voltage
Parameter
Internal reference voltage
ADC sampling time when
reading the internal reference
voltage
Internal reference voltage
spread over the temperature
range
Temperature coefficient
V
DD
= 3 V ±10 mV
Conditions
–40 °C < T
A
< +105 °C
–40 °C < T
A
< +85 °C
Min
1.16
1.16
Typ
1.20
1.20
5.1
Max
1.26
1.24
17.1
(2)
Unit
V
V
µs
T
S_vrefint(1)
V
RERINT
10
100
mV
ppm/°C
T
Coeff(2)
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
5.3.5
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
All I/O pins are in input mode with a static value at V
DD
or V
SS
(no load)
All peripherals are disabled except when explicitly mentioned
The Flash memory access time is adjusted to the f
HCLK
frequency (0 wait state from 0
to 24 MHz, 1 wait state from 24 to 48 MHz and 2 wait states above)
Prefetch in ON (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
PCLK1
= f
HCLK
/2, f
PCLK2
= f
HCLK
The parameters given in
and
are derived from tests performed
under ambient temperature and V
DD
supply voltage conditions summarized in
44/123
Doc ID 14611 Rev 7