欢迎访问ic37.com |
会员登录 免费注册
发布采购

AM29BDS64HE9VKI 参数 Datasheet PDF下载

AM29BDS64HE9VKI图片预览
型号: AM29BDS64HE9VKI
PDF下载: 下载PDF文件 查看货源
内容描述: 128或64兆比特( 8 M或4米×16位) CMOS 1.8伏只同步读/写,突发模式闪存 [128 or 64 Megabit (8 M or 4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory]
分类和应用: 闪存
文件页数/大小: 89 页 / 1587 K
品牌: SPANSION [ SPANSION ]
 浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第41页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第42页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第43页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第44页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第46页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第47页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第48页浏览型号AM29BDS64HE9VKI的Datasheet PDF文件第49页  
D A T A S H E E T  
ing a specific PPB. Unlike the PPB program, no spe-  
PPB Program Command  
cific sector address is required. However, when the  
PPB erase command is written (60h), all Sector PPBs  
are erased in parallel. If the PPB Lock Bit is set, the  
ALL PPB Erase command will not execute and the  
command will time-out without erasing the PPBs. After  
issuing “WP/60h” at the fourth bus cycle, the device re-  
quires a time out period of approximately 1.5 ms to  
erase the PPB. Writing “SBA+WP/40h” at the fifth bus  
cycle produces verify data at DQ0. If DQ0 = 0, the  
PPB is erased. If not, the system must repeat this pro-  
gram sequence from the fourth cycle of “WP/60h”.  
The PPB Program command is used to program, or  
set, a given PPB. Each PPB is individually pro-  
grammed (but is bulk erased with the other PPBs).  
The specific sector address (Amax–A12) are written at  
the same time as the program command 60h. If the  
PPB Lock Bit is set and the correspondingly PPB is  
set for the sector, the PPB Program command will not  
execute and the command will time out without pro-  
gramming the PPB. After issuing “SBA+WP/68h” at  
the fourth bus cycle, the device requires a time out pe-  
riod of approximately 150 µs to program the PPB.  
Writing “SBA+WP/48” at the fifth bus cycle produces  
verify data at DQ0. If DQ0 = 1, the PPB is pro-  
grammed. If not, the system must repeat this program  
sequence from the fourth cycle of “SBA+WP/68h”.  
It is the responsibility of the system to preprogram all  
PPBs prior to issuing the All PPB Erase command. If  
the system attempts to erase a cleared PPB, over-era-  
sure may occur, making it difficult to program the PPB  
at a later time. Also note that the total number of PPB  
program/erase cycles is limited to 100 cycles. Cycling  
the PPBs beyond 100 cycles is not guaranteed.  
The PPB Program command does not follow the  
Embedded Program algorithm. Writing the SecSi  
Sector Exit command or Read/Reset command return  
the device back to normal operation.  
Writing the SecSi Sector Exit command or Read/Re-  
set command return the device to normal operation.  
All PPB Erase Command  
The All PPB Erase command is used to erase all  
PPBs in bulk. There is no means for individually eras-  
May 10, 2006 27024B3  
Am29BDS128H/Am29BDS640H  
43