欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN9215I_07 参数 Datasheet PDF下载

LAN9215I_07图片预览
型号: LAN9215I_07
PDF下载: 下载PDF文件 查看货源
内容描述: 高效的单芯片10/100以太网控制器与HP Auto-MDIX的和工业温度支持 [Highly Efficient Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX and Industrial Temperature Support]
分类和应用: 控制器以太网局域网(LAN)标准
文件页数/大小: 138 页 / 1665 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN9215I_07的Datasheet PDF文件第86页浏览型号LAN9215I_07的Datasheet PDF文件第87页浏览型号LAN9215I_07的Datasheet PDF文件第88页浏览型号LAN9215I_07的Datasheet PDF文件第89页浏览型号LAN9215I_07的Datasheet PDF文件第91页浏览型号LAN9215I_07的Datasheet PDF文件第92页浏览型号LAN9215I_07的Datasheet PDF文件第93页浏览型号LAN9215I_07的Datasheet PDF文件第94页  
Highly Efficient Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX and Industrial Temperature Support  
Datasheet  
5.3.14  
GPIO_CFG—General Purpose IO Configuration Register  
Offset:  
88h  
Size:  
32 bits  
This register configures the GPIO and LED functions.  
BITS  
DESCRIPTION  
TYPE  
DEFAULT  
31  
Reserved  
RO  
-
30:28  
LED[3:1] enable (LEDx_EN). A ‘1’ sets the associated pin as an LED  
output. When cleared low, the pin functions as a GPIO signal.  
LED1/GPIO0 – bit 28  
R/W  
000  
LED2/GPIO1 – bit 29  
LED3/GPIO2 – bit 30  
27  
Reserved  
RO  
-
26:24  
GPIO Interrupt Polarity 0-2 (GPIO_INT_POL). When set high, a high logic  
level on the corresponding GPIO pin will set the corresponding INT_STS  
register bit. When cleared low, a low logic level on the corresponding GPIO  
pin will set the corresponding INT_STS register bit.  
GPIO Interrupts must also be enabled in GPIOx_INT_EN in the INT_EN  
register.  
R/W  
000  
GPIO0 – bit 24  
GPIO1 – bit 25  
GPIO2 – bit 26  
Note:  
GPIO inputs must be active for greater than 40nS to be recognized  
as interrupt inputs.  
23  
Reserved  
RO  
-
22:20  
EEPROM Enable (EEPR_EN). The value of this field determines the  
function of the external EEDIO and EECLK:  
Please refer to Table 5.4 for the EEPROM Enable bit function definitions.  
R/W  
000  
Note:  
The host must not change the function of the EEDIO and EECLK  
pins when an EEPROM read or write cycle is in progress. Do not  
use reserved settings.  
Note:  
Regardless of whether the internal or external PHY is selected,  
RX_DV, TX_CLK and RX_CLK reflect the signals on the internal  
PHY and the MAC always drives TX_EN.  
19  
Reserved  
RO  
-
18:16  
GPIO Buffer Type 0-2 (GPIOBUFn). When set, the output buffer for the  
corresponding GPIO signal is configured as a push/pull driver. When  
cleared, the corresponding GPIO set configured as an open-drain driver.  
GPIO0 – bit 16  
R/W  
000  
GPIO1 – bit 17  
GPIO2 – bit 18  
15:11  
10:8  
Reserved  
RO  
-
GPIO Direction 0-2 (GPDIRn). When set, enables the corresponding GPIO  
as output. When cleared the GPIO is enabled as an input.  
R/W  
0000  
GPIO0 – bit 8  
GPIO1 – bit 9  
GPIO2 – bit 10  
7:5  
Reserved  
RO  
-
Revision 1.93 (12-12-07)  
90  
SMSC LAN9215i  
DATASHEET