欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN9210 参数 Datasheet PDF下载

LAN9210图片预览
型号: LAN9210
PDF下载: 下载PDF文件 查看货源
内容描述: 外形小巧单芯片以太网控制器与HP Auto-MDIX的 [Small Form Factor Single- Chip Ethernet Controller with HP Auto-MDIX]
分类和应用: 控制器以太网
文件页数/大小: 458 页 / 4618 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN9210的Datasheet PDF文件第285页浏览型号LAN9210的Datasheet PDF文件第286页浏览型号LAN9210的Datasheet PDF文件第287页浏览型号LAN9210的Datasheet PDF文件第288页浏览型号LAN9210的Datasheet PDF文件第290页浏览型号LAN9210的Datasheet PDF文件第291页浏览型号LAN9210的Datasheet PDF文件第292页浏览型号LAN9210的Datasheet PDF文件第293页  
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface  
Datasheet  
BITS  
DESCRIPTION  
TYPE  
DEFAULT  
9
Restart Auto-Negotiation (PHY_RST_AN)  
When set, this bit restarts the Auto-Negotiation process.  
R/W  
SC  
0b  
0: Normal operation  
1: Auto-Negotiation restarted  
8
7
Duplex Mode (PHY_DUPLEX)  
R/W  
R/W  
Note 14.51  
This bit is used to set the duplex when the Auto-Negotiation (PHY_AN) bit  
is disabled.  
0: Half Duplex  
1: Full Duplex  
Collision Test Mode (PHY_COL_TEST)  
0b  
This bit enables/disables the collision test mode of the Port x PHY. When  
set, the collision signal is active during transmission. It is recommended that  
this feature be used only in loopback mode.  
0: Collision test mode disabled  
1: Collision test mode enabled  
6:0  
RESERVED  
RO  
-
Note 14.49 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap  
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and the speed select  
strap (speed_strap_1 for Port 1 PHY, speed_strap_2 for Port 2 PHY). Essentially, if the  
Auto-Negotiation strap is set, the default value is 1, otherwise the default is determined by  
the value of the speed select strap. Refer to Section 4.2.4, "Configuration Straps," on  
page 40 for more information.  
Note 14.50 The default value of this bit is determined by the value of the Auto-Negotiation strap  
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY). Refer to Section 4.2.4,  
"Configuration Straps," on page 40 for more information.  
Note 14.51 The default value of this bit is determined by the logical AND of the negation of the Auto-  
Negotiation strap (autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and  
the duplex select strap (duplex_strap_1 for Port 1 PHY, duplex_strap_2 for Port 2 PHY).  
Essentially, if the Auto-Negotiation strap is set, the default value is 0, otherwise the default  
is determined by the value of the duplex select strap. Refer to Section 4.2.4, "Configuration  
Straps," on page 40 for more information.  
SMSC LAN9312  
289  
Revision 1.2 (04-08-08)  
DATASHEET  
 复制成功!