欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN8700IC-AEZG 参数 Datasheet PDF下载

LAN8700IC-AEZG图片预览
型号: LAN8700IC-AEZG
PDF下载: 下载PDF文件 查看货源
内容描述: [LAN Controller, 4 Channel(s), 12.5MBps, CMOS, 6 X 6 MM, 0.90 MM HEIGHT, ROHS COMPLIANT, QFN-36]
分类和应用: 通信时钟局域网数据传输外围集成电路
文件页数/大小: 83 页 / 687 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN8700IC-AEZG的Datasheet PDF文件第21页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第22页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第23页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第24页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第26页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第27页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第28页浏览型号LAN8700IC-AEZG的Datasheet PDF文件第29页  
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint  
Datasheet  
In order to comply with legacy 10Base-T MAC/Controllers, in Half-duplex mode the PHY loops back  
the transmitted data, on the receive path. This does not confuse the MAC/Controller since the COL  
signal is not asserted during this time. The PHY also supports the SQE (Heartbeat) signal. See Section  
5.4.2, "Collision Detect," on page 51, for more details.  
For RMII, TXD[1:0] shall transition synchronously with respect to REF_CLK. When TX_EN is asserted,  
TXD[1:0] are accepted for transmission by the LAN8700/LAN8700i. TXD[1:0] shall be “00” to indicate  
idle when TX_EN is deasserted. Values of TXD[1:0] other than “00” when TX_EN is deasserted are  
reserved for out-of-band signalling (to be defined). Values other than “00” on TXD[1:0] while TX_EN is  
deasserted shall be ignored by the LAN8700/LAN8700i.TXD[1:0] shall provide valid data for each  
REF_CLK period while TX_EN is asserted.  
4.4.2  
Manchester Encoding  
The 4-bit wide data is sent to the TX10M block. The nibbles are converted to a 10Mbps serial NRZI  
data stream. The 10M PLL locks onto the external clock or internal oscillator and produces a 20MHz  
clock. This is used to Manchester encode the NRZ data stream. When no data is being transmitted  
(TX_EN is low), the TX10M block outputs Normal Link Pulses (NLPs) to maintain communications with  
the remote link partner.  
4.4.3  
10M Transmit Drivers  
The Manchester encoded data is sent to the analog transmitter where it is shaped and filtered before  
being driven out as a differential signal across the TXP and TXN outputs.  
4.5  
10Base-T Receive  
The 10Base-T receiver gets the Manchester- encoded analog signal from the cable via the magnetics.  
It recovers the receive clock from the signal and uses this clock to recover the NRZI data stream. This  
10M serial data is converted to 4-bit data nibbles which are passed to the controller across the MII at  
a rate of 2.5MHz.  
This 10M receiver uses the following blocks:  
„
„
„
„
Filter and SQUELCH (analog)  
10M PLL (analog)  
RX 10M (digital)  
MII (digital)  
4.5.1  
4.5.2  
10M Receive Input and Squelch  
The Manchester signal from the cable is fed into the PHY (on inputs RXP and RXN) via 1:1 ratio  
magnetics. It is first filtered to reduce any out-of-band noise. It then passes through a SQUELCH  
circuit. The SQUELCH is a set of amplitude and timing comparators that normally reject differential  
voltage levels below 300mV and detect and recognize differential voltages above 585mV.  
Manchester Decoding  
The output of the SQUELCH goes to the RX10M block where it is validated as Manchester encoded  
data. The polarity of the signal is also checked. If the polarity is reversed (local RXP is connected to  
RXN of the remote partner and vice versa), then this is identified and corrected. The reversed condition  
is indicated by the flag “XPOL“, bit 4 in register 27. The 10M PLL is locked onto the received  
Manchester signal and from this, generates the received 20MHz clock. Using this clock, the  
Manchester encoded data is extracted and converted to a 10MHz NRZI data stream. It is then  
converted from serial to 4-bit wide parallel data.  
SMSC LAN8700/LAN8700i  
Revision 2.3 (04-12-11)  
DATA2S5HEET