欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAP1088-1-CP-TR 参数 Datasheet PDF下载

CAP1088-1-CP-TR图片预览
型号: CAP1088-1-CP-TR
PDF下载: 下载PDF文件 查看货源
内容描述: 8通道电容式触摸传感器,具有8个LED驱动器 [8 Channel Capacitive Touch Sensor with 8 LED Drivers]
分类和应用: 驱动器模拟IC传感器信号电路
文件页数/大小: 72 页 / 994 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第11页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第12页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第13页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第14页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第16页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第17页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第18页浏览型号CAP1088-1-CP-TR的Datasheet PDF文件第19页  
8 Channel Capacitive Touch Sensor with 8 LED Drivers  
Datasheet  
Chapter 3 Communications  
3.1  
Communications  
The CAP1088 communicates using the 2-wire SMBus or I2C bus, the 2-wire proprietary BC-Link, or  
the SPI bus. Regardless of communication mechanism, the device functionality remains unchanged.  
The communications mechanism as well as the SMBus (or I2C) slave address is determined by the  
resistor connected between the ADDR_COMM pin and ground as shown in Table 3.1.  
Table 3.1 ADDR_COMM Pin Decode  
PULL-DOWN RESISTOR (+/- 5%)  
PROTOCOL USED  
SMBUS ADDRESS  
<= 47k  
56k  
SPI Communications using  
Normal 4-wire Protocol Used  
n/a  
SPI Communications using Bi-  
Directional 3-wire Protocol Used  
n/a  
68k  
82k  
BC-Link Communications  
SMBus / I2C  
n/a  
0101_100(r/w)  
0101_011(r/w)  
0101_010(r/w)  
0101_001(r/w)  
0101_000(r/w)  
100k  
120k  
150k  
VDD  
SMBus / I2C  
SMBus / I2C  
SMBus / I2C  
SMBus / I2C  
2
3.1.1  
SMBus (I C) Communications  
When configured to communicate via the SMBus, the CAP1088 supports the following protocols: Send  
Byte, Receive Byte, Read Byte, and Write Byte. In addition, the device supports I2C formatting for block  
read and block write protocols.  
APPLICATION NOTE: For SMBus/I2C communications, the SPI_CS# pin is not used and should be grounded; any  
data presented to this pin will be ignored.  
See Section 3.2 and Section 3.3 for more information on the SMBus bus and protocols respectively.  
3.1.2  
3.1.3  
SPI Communications  
When configured to communicate via the SPI bus, the CAP1088 supports both bi-directional 3-wire  
and normal 4-wire protocols and uses the SPI_CS# pin to enable communications.  
See Section 3.4 and Section 3.5 for more information on the SPI bus and protocols respectively.  
BC-Link Communications  
When BC-Link communications are used, the CAP1088 supports the read byte protocol and the write  
byte protocol.  
APPLICATION NOTE: For BC-Link communications, the SPI_CS# pin is not used and should be grounded; any  
data presented to this pin will be ignored.  
See Section 3.7 for more information on the BC-Link Bus and protocols respectively.  
SMSC CAP1088  
Revision 1.1 (08-05-09)  
DATA1S5HEET