欢迎访问ic37.com |
会员登录 免费注册
发布采购

SI1002-C-GM 参数 Datasheet PDF下载

SI1002-C-GM图片预览
型号: SI1002-C-GM
PDF下载: 下载PDF文件 查看货源
内容描述: 超低功耗, 64/32 KB , 10位ADC, MCU ,集成了240-960兆赫的EZRadioPRO收发器 [Ultra Low Power, 64/32 kB, 10-Bit ADC MCU with Integrated 240-960 MHz EZRadioPRO Transceiver]
分类和应用:
文件页数/大小: 376 页 / 2369 K
品牌: SILICON [ SILICON ]
 浏览型号SI1002-C-GM的Datasheet PDF文件第235页浏览型号SI1002-C-GM的Datasheet PDF文件第236页浏览型号SI1002-C-GM的Datasheet PDF文件第237页浏览型号SI1002-C-GM的Datasheet PDF文件第238页浏览型号SI1002-C-GM的Datasheet PDF文件第240页浏览型号SI1002-C-GM的Datasheet PDF文件第241页浏览型号SI1002-C-GM的Datasheet PDF文件第242页浏览型号SI1002-C-GM的Datasheet PDF文件第243页  
Si1000/1/2/3/4/5  
23. EZRadioPRO® 240–960 MHz Transceiver  
Si1000/1/2/3/4/5 devices include the EZRadioPRO family of ISM wireless transceivers with continuous fre-  
quency tuning over 240–960 MHz. The wide operating voltage range of 1.8–3.6 V and low current con-  
sumption makes the EZRadioPRO an ideal solution for battery powered applications.  
The EZRadioPRO transceiver operates as a time division duplexing (TDD) transceiver where the device  
alternately transmits and receives data packets. The device uses a single-conversion mixer to downcon-  
vert the 2-level FSK/GFSK/OOK modulated receive signal to a low IF frequency. Following a programma-  
ble gain amplifier (PGA) the signal is converted to the digital domain by a high performance  ADC  
allowing filtering, demodulation, slicing, and packet handling to be performed in the built-in DSP increasing  
the receiver’s performance and flexibility versus analog based architectures. The demodulated signal is  
then output to the system MCU through a programmable GPIO or via the standard SPI bus by reading the  
64-byte RX FIFO.  
A single high precision local oscillator (LO) is used for both transmit and receive modes since the transmit-  
ter and receiver do not operate at the same time. The LO is generated by an integrated VCO and  Frac-  
tional-N PLL synthesizer. The synthesizer is designed to support configurable data rates, output frequency  
and frequency deviation at any frequency between 240–960 MHz. The transmit FSK data is modulated  
directly into the  data stream and can be shaped by a Gaussian low-pass filter to reduce unwanted  
spectral content.  
The Si1000’s PA output power can be configured between –1 and +20 dBm in 3 dB steps, while the  
Si1002/3/4/5's PA output power can be configured between –8 and +13 dBm in 3 dB steps. The PA is sin-  
gle-ended to allow for easy antenna matching and low BOM cost. The PA incorporates automatic ramp-up  
and rampdown control to reduce unwanted spectral spreading. The +20 dBm power amplifier of the  
Si1000/1 can also be used to compensate for the reduced performance of a lower cost, lower performance  
antenna or antenna with size constraints due to a small form-factor. Competing solutions require large and  
expensive external PAs to achieve comparable performance. The EZRadioPRO transceivers support fre-  
quency hopping, TX/RX switch control, and antenna diversity switch control to extend the link range and  
improve performance.  
The EZRadioPRO peripheral also controls three GPIO pins: GPIO_0, GPIO_1, and GPIO_2. See Applica-  
tion Note “AN415: EZRadioPRO Programming Guide“ for details on initializing and using the EZRadioPRO  
peripheral.  
Rev. 1.0  
239