欢迎访问ic37.com |
会员登录 免费注册
发布采购

K4E151611D 参数 Datasheet PDF下载

K4E151611D图片预览
型号: K4E151611D
PDF下载: 下载PDF文件 查看货源
内容描述: 1米x 16Bit的CMOS动态随机存储器与扩充数据输出 [1M x 16Bit CMOS Dynamic RAM with Extended Data Out]
分类和应用: 存储
文件页数/大小: 35 页 / 551 K
品牌: SAMSUNG [ SAMSUNG SEMICONDUCTOR ]
 浏览型号K4E151611D的Datasheet PDF文件第3页浏览型号K4E151611D的Datasheet PDF文件第4页浏览型号K4E151611D的Datasheet PDF文件第5页浏览型号K4E151611D的Datasheet PDF文件第6页浏览型号K4E151611D的Datasheet PDF文件第8页浏览型号K4E151611D的Datasheet PDF文件第9页浏览型号K4E151611D的Datasheet PDF文件第10页浏览型号K4E151611D的Datasheet PDF文件第11页  
K4E171611D, K4E151611D
K4E171612D, K4E151612D
NOTES
CMOS DRAM
1. An initial pause of 200us is required after power-up followed by any 8 RAS-only refresh or CAS-before-RAS refresh cycles
before proper device operation is achieved.
2. Input voltage levels are Vih/Vil. V
IH
(min) and V
IL
(max) are reference levels for measuring timing of input signals.
Transition times are measured between V
IH
(min) and V
IL
(max) and are assumed to be 2ns for all inputs.
3. Measured with a load equivalent to 2 TTL(5V)/1TTL(3.3V) loads and 100pF.
4. Operation within the
t
RCD
(max) limit insures that
t
RAC
(max) can be met.
t
RCD
(max) is specified as a reference point only.
If
t
RCD
is greater than the specified
t
RCD
(max) limit, then access time is controlled exclusively by
t
CAC
.
5. Assumes that t
RCD
t
RCD
(max).
6. This parameter defines the time at which the output achieves the open circuit condition and is not referenced to V
oh
or V
ol
.
7.
t
WCS
,
t
RWD
,
t
CWD
,
t
AWD
and
t
CPWD
are non restrictive operating parameters. They are included in the data sheet as electrical
characteristics only. If
t
WCS
t
WCS
(min), the cycle is an early write cycle and the data output will remain high impedance for the
duration of the cycle. If
t
CWD
t
CWD
(min),
t
RWD
t
RWD
(min),
t
AWD
t
AWD
(min) and
t
CPWD
t
CPWD
(min), then the cycle is a read-
modify-write cycle and the data output will contain the data read from the selected address. If neither of the above conditions
is satisfied, the condition of the data out is indeterminate.
8. Either
t
RCH
or
t
RRH
must be satisfied for a read cycle.
9. These parameters are referenced to CAS falling edge in early write cycles and to W falling edge in OE controlled write cycle
and read-modify-write cycles.
10. Operation within the
t
RAD
(max) limit insures that
t
RAC
(max) can be met.
t
RAD
(max) is specified as a reference point only.
If
t
RAD
is greater than the specified
t
RAD
(max) limit, then access time is controlled by
t
AA
.
K4E17(5)1611(2)D Truth Table
RAS
H
L
L
L
L
L
L
L
L
LCAS
X
H
L
H
L
L
H
L
L
UCAS
X
H
H
L
L
H
L
L
L
W
X
X
H
H
H
L
L
L
H
OE
X
X
L
L
L
H
H
H
H
DQ0 - DQ7
Hi-Z
Hi-Z
DQ-OUT
Hi-Z
DQ-OUT
DQ-IN
-
DQ-IN
Hi-Z
DQ8-DQ15
Hi-Z
Hi-Z
Hi-Z
DQ-OUT
DQ-OUT
-
DQ-IN
DQ-IN
Hi-Z
STATE
Standby
Refresh
Byte Read
Byte Read
Word Read
Byte Write
Byte Write
Word Write
-