欢迎访问ic37.com |
会员登录 免费注册
发布采购

FM32L274-G 参数 Datasheet PDF下载

FM32L274-G图片预览
型号: FM32L274-G
PDF下载: 下载PDF文件 查看货源
内容描述: 3V集成处理器伴侣与记忆 [3V Integrated Processor Companion with Memory]
分类和应用:
文件页数/大小: 21 页 / 275 K
品牌: RAMTRON [ RAMTRON INTERNATIONAL CORPORATION ]
 浏览型号FM32L274-G的Datasheet PDF文件第1页浏览型号FM32L274-G的Datasheet PDF文件第2页浏览型号FM32L274-G的Datasheet PDF文件第4页浏览型号FM32L274-G的Datasheet PDF文件第5页浏览型号FM32L274-G的Datasheet PDF文件第6页浏览型号FM32L274-G的Datasheet PDF文件第7页浏览型号FM32L274-G的Datasheet PDF文件第8页浏览型号FM32L274-G的Datasheet PDF文件第9页  
FM32L278/L276/L274/L272 - 3V I2C Companion  
FRAM  
Array  
2-Wire  
Interface  
A1, A0  
SCL  
LockOut  
SDA  
LockOut  
Special  
Function  
Registers  
RST  
Watchdog  
LV Detect  
S/N  
PFI  
CNT1  
Event  
+
-
Counters  
PFO  
CNT2  
1.2V  
-
2.5V  
+
VDD  
Switched Power  
VBAK  
Battery Backed  
Nonvolatile  
Figure 1. Block Diagram  
Pin Descriptions  
Pin Name  
Type Pin Description  
A0, A1  
Input  
Device select inputs are used to address multiple memories on a serial bus. To select the  
device the address value on the two pins must match the corresponding bits contained in  
the device address. The device select pins are pulled down internally.  
CNT1,  
CNT2  
Input  
Event Counter Inputs: These battery-backed inputs increment counters when an edge is  
detected on the corresponding CNT pin. The polarity is programmable. These pins  
should not be left floating. Tie to ground if pins are not used.  
PFO  
/RST  
SDA  
Output Power Fail Output: This is the early power-fail output.  
I/O  
I/O  
Active low reset output with weak pull-up. Also input for manual reset.  
Serial Data & Address: This is a bi-directional line for the two-wire interface. It is open-  
drain and is intended to be wire-OR’d with other devices on the two-wire bus. The input  
buffer incorporates a Schmitt trigger for noise immunity and the output driver includes  
slope control for falling edges. A pull-up resistor is required.  
Serial Clock: The serial clock line for the two-wire interface. Data is clocked out of the  
part on the falling edge, and in on the rising edge. The SCL input also incorporates a  
Schmitt trigger input for noise immunity.  
Early Power-fail Input: Typically connected to an unregulated power supply to detect an  
early power failure. This pin should not be left floating.  
SCL  
Input  
Input  
PFI  
VBAK  
Supply Backup supply voltage: A 3V battery or a large value capacitor. If no backup supply is  
used, this pin should be tied to ground and the VBC bit should be cleared. The trickle  
charger is UL recognized and ensures no excessive current when using a lithium battery.  
Supply Supply Voltage  
VDD  
VSS  
Supply Ground  
Rev. 3.0  
Feb. 2009  
Page 3 of 21  
 复制成功!