FM24W256 - 256Kb Wide Voltage I2C F-RAM
Memory Operation
Slave ID
Device Select
1
7
0
6
1
5
0
4
A2
3
A1
2
A0
1
R/W
0
Figure 4. Slave Address
Addressing Overview
After the FM24W256 (as receiver) acknowledges the
slave address, the master can place the memory
address on the bus for a write operation. The address
requires two bytes. The first is the MSB. Since the
device uses only 15 address bits, the value of the
upper bit is “don’t care”. Following the MSB is the
LSB with the remaining eight address bits. The
address value is latched internally. Each access
causes the latched address value to be incremented
automatically. The current address is the value that is
held in the latch -- either a newly written value or the
address following the last access. The current address
will be held for as long as power remains or until a
new value is written. Reads always use the current
address. A random read address can be loaded by
beginning a write operation as explained below.
After transmission of each data byte, just prior to the
acknowledge, the FM24W256 increments the internal
address latch. This allows the next sequential byte to
be accessed with no additional addressing. After the
last address (7FFFh) is reached, the address latch will
roll over to 0000h. There is no limit to the number of
bytes that can be accessed with a single read or write
operation.
Data Transfer
After the address information has been transmitted,
data transfer between the bus master and the
FM24W256 can begin. For a read operation the
FM24W256 will place 8 data bits on the bus then
wait for an acknowledge from the master. If the
acknowledge occurs, the FM24W256 will transfer the
next sequential byte. If the acknowledge is not sent,
the FM24W256 will end the read operation. For a
write operation, the FM24W256 will accept 8 data
bits from the master then send an acknowledge. All
data transfer occurs MSB (most significant bit) first.
The FM24W256 is designed to operate in a manner
very similar to other 2-wire interface memory
products. The major differences result from the
higher performance write capability of F-RAM
technology. These improvements result in some
differences between the FM24W256 and a similar
configuration EEPROM during writes. The
complete operation for both writes and reads is
explained below.
Write Operation
All writes begin with a slave address, then a
memory address. The bus master indicates a write
operation by setting the LSB of the slave address to
a 0. After addressing, the bus master sends each byte
of data to the memory and the memory generates an
acknowledge condition. Any number of sequential
bytes may be written. If the end of the address range
is reached internally, the address counter will wrap
from 7FFFh to 0000h.
Unlike other nonvolatile memory technologies,
there is no effective write delay with F-RAM. Since
the read and write access times of the underlying
memory are the same, the user experiences no delay
through the bus. The entire memory cycle occurs in
less time than a single bus clock. Therefore, any
operation including read or write can occur
immediately following a write. Acknowledge
polling, a technique used with EEPROMs to
determine if a write is complete is unnecessary and
will always return a ready condition.
Internally, an actual memory write occurs after the
8
th
data bit is transferred. It will be complete before
the acknowledge is sent. Therefore, if the user
desires to abort a write without altering the memory
contents, this should be done using start or stop
condition prior to the 8
th
data bit. The FM24W256
uses no page buffering.
The memory array can be write protected using the
WP pin. Setting the WP pin to a high condition
(V
DD
) will write-protect all addresses. The
FM24W256 will not acknowledge data bytes that
are written to protected addresses. In addition, the
address counter will not increment if writes are
attempted to these addresses. Setting WP to a low
state (V
SS
) will deactivate this feature. WP is pulled
down internally.
Figures 5 and 6 below illustrate a single-byte and
multiple-byte write cycles.
Rev. 1.3
July 2011
Page 5 of 13
RAMTRON [ RAMTRON INTERNATIONAL CORPORATION ]
