欢迎访问ic37.com |
会员登录 免费注册
发布采购

QN8006B 参数 Datasheet PDF下载

QN8006B图片预览
型号: QN8006B
PDF下载: 下载PDF文件 查看货源
内容描述: 高性能数字FM收发器用于便携式设备 [High Performance Digital FM Transceiver for Portable Devices]
分类和应用: 便携式便携式设备
文件页数/大小: 58 页 / 1852 K
品牌: QUANTUM [ QUANTUM RESEARCH GROUP ]
 浏览型号QN8006B的Datasheet PDF文件第27页浏览型号QN8006B的Datasheet PDF文件第28页浏览型号QN8006B的Datasheet PDF文件第29页浏览型号QN8006B的Datasheet PDF文件第30页浏览型号QN8006B的Datasheet PDF文件第32页浏览型号QN8006B的Datasheet PDF文件第33页浏览型号QN8006B的Datasheet PDF文件第34页浏览型号QN8006B的Datasheet PDF文件第35页  
QN8006B/8006LB  
REGISTER  
59h  
NAME  
PAC_CAL  
PAG_CAL  
USER CONTROL FUNCTIONS  
PA tuning cap calibration.  
PA gain calibration.  
5Ah  
Register Bit R/W Status:  
RO - Read Only: You can not program these bits.  
WO - Write Only: You can write and read these bits; the value you read back will be the same as written.  
R/W - Read/Write: You can write and read these bits; the value you read back can be different from the value written.  
Typically, the value is set by the chip itself. This could be a calibration result, AGC FSM result, etc.  
Word: SYSTEM1  
Address: 00h  
Bit 7  
Bit 0  
(LSB)  
Bit 6  
Bit 5  
Bit 4  
Bit 3  
Bit 2  
Bit 1  
(MSB)  
rxreq  
wo  
txreq  
wo  
chsc  
wo  
stnby  
wo  
rxi2s  
wo  
txi2s  
wo  
rdsen  
wo  
cca_ch_dis  
wo  
Bit  
Symbol  
Default  
Description  
7
6
5
RXREQ  
0
0
0
Receiving request (overwrites TXREQ and STNBY):  
0
1
Non RX mode. Either IDLE, standby or TX mode.  
Enter Receiving mode.  
TXREQ  
CHSC  
Transmission request:  
0
1
Non TX mode. Either IDLE, standby or RX mode.  
Enter Transmit mode.  
Channel Scan mode enable: Combined with TXREQ and RXREQ, chip  
scans for occupied channel for receiving or empty channel for transmission.  
After completing channel scanning, this bit will be cleared automatically.  
For CCS (TX Scan), the clearest channel (channel with weakest RSSI) will  
be selected (if TXCCAA is not equal to zero, another prior condition  
should be met, see description of CCA register at 19h).  
For RX Scan, the FIRST valid channel will be selected. To start CCA/CCS,  
set CHSC (REG0 [5]) to 1. CHSH will be automatically cleared to 0 when  
CCA/CCS is complete. To use the scanned channel, set CCA_CH_DIS to  
0. (CCA_CH_DIS can be set to 0 at the same time CHSC=1).  
0
1
Normal operation.  
Channel Scan mode operation.  
4
3
STNBY  
RXI2S  
0
0
Request immediately to enter Standby mode if the chip is in IDLE and no  
TXREQ or RXREQ is received.  
0
1
Non standby mode. Either IDLE, TX mode or RX mode.  
Enter standby mode.  
I2S enable in receiving mode:  
Rev 2.08 (04/10)  
Copyright ©2010 by Quintic Corporation  
Page 31  
Confidential A  
Confidential Information contained herein is covered under Non-Disclosure Agreement (NDA).  
 复制成功!