欢迎访问ic37.com |
会员登录 免费注册
发布采购

PFS7329H 参数 Datasheet PDF下载

PFS7329H图片预览
型号: PFS7329H
PDF下载: 下载PDF文件 查看货源
内容描述: 高功率PFC控制器,集成高压MOSFET和二极管Qspeed的 [High Power PFC Controller with Integrated High-Voltage MOSFET and Qspeed Diode]
分类和应用: 二极管功率因数校正高压控制器
文件页数/大小: 30 页 / 4360 K
品牌: POWERINT [ Power Integrations ]
 浏览型号PFS7329H的Datasheet PDF文件第7页浏览型号PFS7329H的Datasheet PDF文件第8页浏览型号PFS7329H的Datasheet PDF文件第9页浏览型号PFS7329H的Datasheet PDF文件第10页浏览型号PFS7329H的Datasheet PDF文件第12页浏览型号PFS7329H的Datasheet PDF文件第13页浏览型号PFS7329H的Datasheet PDF文件第14页浏览型号PFS7329H的Datasheet PDF文件第15页  
PFS7323-7329  
Hysteretic Thermal Shutdown  
after the thermal fault is below IUV+, OTP hysteresis is disabled,  
however if the peak input voltage after the thermal fault is above  
IUV+ then the OTP hysteresis is enabled prior to re-initiating the  
soft-start sequence.  
The thermal shutdown circuitry senses the controller die  
temperature. The threshold is set at 117 °C typical with a 49 °C  
hysteresis. When the die temperature rises above this threshold  
(OTP) (117 °C +8/-7 °C), the controller initiates a fast soft-  
shutdown and remains disabled until the die temperature falls  
by ~49°C, at which point the device will re-initiate the soft-start  
sequence.  
The maximum time delay for soft-shutdown to occur after an  
OTP event is detected is tREFRESH  
.
In the event the input voltage is reduced below the brown-in  
threshold and an OTP event occurs (no OTP hysteresis) and the  
input voltage is raised immediately above brown-in before the  
controller junction temperature falls below the OTP threshold,  
the controller will initiate a soft-start once the controller junction  
is just below the OTP threshold. Depending on the system  
thermal conditions, the controller could initiate OTP shutdown  
again because of insufficient time to cool down the controller.  
The OTP shutdown that occurs when the input voltage is above  
brown-in will have hysteresis enabled.  
In the event an OTP is detected when the VOLTAGE MONITOR  
pin current is below IUV+ threshold, the device will initiate a  
soft-shutdown and remain disabled until all the conditions for  
the start-up (soft-start sequence) are satisfied. In this mode of  
operation the OTP hysteresis is disabled.  
When soft-shutdown is initiated by an over-temperature fault  
(OTP) the brown-out timer delay (tBROWN-OUT) is disabled. The  
behavior of OTP depends on the input voltage peak detected  
following the thermal fault. If the input peak voltage detected  
Output Power Table  
eSIP Package  
Efficiency Power Mode R = 49.9 kW  
Maximum Continuous  
Full Power Mode R = 24.9 kW  
Maximum Continuous  
Product  
Output Power Rating at  
Output Power Rating at  
Peak Output Power  
Rating at 90 VAC4  
Peak Output Power  
Rating at 90 VAC4  
90 VAC2  
90 VAC2  
Minimum3  
60 W  
Maximum  
80 W  
Minimum3  
85 W  
Maximum  
110 W  
PFS7323L  
PFS7324L  
PFS7325L  
PFS7326H  
PFS7327H  
PFS7328H  
PFS7329H  
90 W  
120 W  
165 W  
205 W  
255 W  
310 W  
345 W  
120 W  
150 W  
205 W  
260 W  
320 W  
385 W  
425 W  
80 W  
110 W  
150 W  
185 W  
230 W  
280 W  
320 W  
100 W  
140 W  
180 W  
220 W  
270 W  
293 W  
130 W  
185 W  
230 W  
290 W  
350 W  
380 W  
110 W  
140 W  
175 W  
210 W  
235 W  
Table 2. Output Power Table.  
Notes:  
1. See Key Application considerations.  
2. Maximum practical continuous power at 90 VAC in an open-frame design with adequate heat sinking, measured at 50 °C ambient.  
3. Recommended lower range of maximum continuous power for best light load efficiency; HiperPFS-2 will operate and perform below this level.  
4. Internal output power limit.  
11  
www.powerint.com  
Rev. B 06/13