欢迎访问ic37.com |
会员登录 免费注册
发布采购

PM8621 参数 Datasheet PDF下载

PM8621图片预览
型号: PM8621
PDF下载: 下载PDF文件 查看货源
内容描述: NSE- 8G⑩标准产品数据表初步 [NSE-8G⑩ Standard Product Data Sheet Preliminary]
分类和应用:
文件页数/大小: 184 页 / 957 K
品牌: PMC [ PMC-SIERRA, INC ]
 浏览型号PM8621的Datasheet PDF文件第26页浏览型号PM8621的Datasheet PDF文件第27页浏览型号PM8621的Datasheet PDF文件第28页浏览型号PM8621的Datasheet PDF文件第29页浏览型号PM8621的Datasheet PDF文件第31页浏览型号PM8621的Datasheet PDF文件第32页浏览型号PM8621的Datasheet PDF文件第33页浏览型号PM8621的Datasheet PDF文件第34页  
NSE-8G™ Standard Product Data Sheet  
Preliminary  
Pad Name  
ALE  
Type  
Input  
Pin No.  
AL30  
Function  
Address Latch Enable. The address latch enable signal  
(ALE) is active high and latches the address bus  
(A[11:0]) when it is set low. The internal address latches  
are transparent when ALE is set high. ALE allows the  
NSE-8G to interface to a multiplexed address/data bus.  
ALE has an integral pull up resistor.  
Interrupt Request Bar. The active low interrupt enable  
signal (INTB) output goes low when an NSE-8G interrupt  
source is active and that source is unmasked. INTB  
returns high when the interrupt is acknowledged via an  
appropriate register access. INTB is an open drain  
output.  
INTB  
Open Drain  
Output  
AN30  
JTAG Port (5 Balls)  
TCK  
Input  
Input  
B14  
B13  
Test Clock. The JTAG test clock signal (TCK) provides  
timing for test operations that are carried out using the  
IEEE P1149.1 test access port.  
Test Mode Select. The JTAG test mode select signal  
(TMS) controls the test operations that are carried out  
using the IEEE P1149.1 test access port. TMS is  
sampled on the rising edge of TCK. TMS has an integral  
pull-up resistor.  
TMS  
TDI  
Input  
C12  
C11  
Test Data Input. The JTAG test data input signal (TDI)  
carries test data into the NSE-8G via the IEEE P1149.1  
test access port. TDI is sampled on the rising edge of  
TCK. TDI has an integral pull-up resistor.  
Test Data Output. TheJTAG test data output signal  
(TDO) carries test data out of the NSE-8G via the IEEE  
P1149.1 test access port. TDO is updated on the falling  
edge of TCK. TDO is a tri-state output which is inactive  
except when scanning of data is in progress.  
TDO  
Tri-state  
Test Reset Bar. The active low JTAG test reset signal  
(TRSTB) provides an asynchronous NSE-8G test access  
port reset via the IEEE P1149.1 test access port. TRSTB  
is a Schmitt triggered input with an integral pull-up  
resistor.  
TRSTB  
Input  
D14  
Note that when TRSTB is not being used, it must be  
connected to the RSTB input.  
Proprietary and Confidential to PMC-Sierra, Inc., and for its Customers’ Internal Use  
Document ID: PMC-2010850, Issue 1  
29  
 复制成功!