Philips Semiconductors
LPC2364/2366/2368
Fast communication chip
Table 3.
Symbol
Pin description
…continued
Pin
Type
location
80
I/O
I/O
O
I
Description
P0.5 —
General purpose digital input/output pin.
I2SRX_WS —
Receive Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I
2
S-bus specification.
TD2 —
CAN2 transmitter output.
CAP2.1 —
Capture input for Timer 2, channel 1.
P0.6 —
General purpose digital input/output pin.
I2SRX_SDA —
Receive data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I
2
S-bus specification.
SSEL1 —
Slave Select for SSP1.
MAT2.0 —
Match output for Timer 2, channel 0.
P0.7 —
General purpose digital input/output pin.
I2STX_CLK —
Transmit Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I
2
S-bus specification.
SCK1 —
Serial Clock for SSP1.
MAT2.1 —
Match output for Timer 2, channel 1.
P0.8 —
General purpose digital input/output pin.
I2STX_WS —
Transmit Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I
2
S-bus specification.
MISO1 —
Master In Slave Out for SSP1.
MAT2.2 —
Match output for Timer 2, channel 2.
P0.9 —
General purpose digital input/output pin.
I2STX_SDA —
Transmit data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I
2
S-bus specification.
MOSI1 —
Master Out Slave In for SSP1.
MAT2.3 —
Match output for Timer 2, channel 3.
P0.10 —
General purpose digital input/output pin.
TXD2 —
Transmitter output for UART2.
SDA2 —
I
2
C2 data input/output (this is not an open drain pin).
MAT3.0 —
Match output for Timer 3, channel 0.
P0.11 —
General purpose digital input/output pin.
RXD2 —
Receiver input for UART2.
SCL2 —
I
2
C2 clock input/output (this is not an open drain pin).
MAT3.1 —
Match output for Timer 3, channel 1.
P0.15 —
General purpose digital input/output pin.
TXD1 —
Transmitter output for UART1.
SCK0 —
Serial clock for SSP0.
SCK —
Serial clock for SPI.
P0.16 —
General purpose digital input/output pin.
RXD1 —
Receiver input for UART1.
SSEL0 —
Slave Select for SSP0.
SSEL —
Slave Select for SPI.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
P0.5/
I2SRX_WS/
TD2/CAP2.1
P0.6/
I2SRX_SDA/
SSEL1/MAT2.0
79
I/O
I/O
I/O
O
P0.7/
I2STX_CLK/
SCK1/MAT2.1
78
I/O
I/O
I/O
O
P0.8/
I2STX_WS/
MISO1/MAT2.2
77
I/O
I/O
I/O
O
P0.9/
I2STX_SDA/
MOSI1/MAT2.3
76
I/O
I/O
I/O
O
P0.10/TXD2/
SDA2/MAT3.0
48
I/O
O
I/O
O
P0.11/RXD2/
SCL2/MAT3.1
49
I/O
I
I/O
O
P0.15/TXD1/
SCK0/SCK
62
I/O
O
I/O
I/O
P0.16/RXD1/
SSEL0/SSEL
63
I/O
I
I/O
I/O
LPC2364_66_68_1
Preliminary data sheet
Rev. 01 — 22 September 2006
6 of 48
PHILIPS [ NXP SEMICONDUCTORS ]
