欢迎访问ic37.com |
会员登录 免费注册
发布采购

LM25069 参数 Datasheet PDF下载

LM25069图片预览
型号: LM25069
PDF下载: 下载PDF文件 查看货源
内容描述: 正低电压功率限制热插拔控制器 [Positive Low Voltage Power Limiting Hot Swap Controller]
分类和应用: 控制器
文件页数/大小: 24 页 / 597 K
品牌: NSC [ National Semiconductor ]
 浏览型号LM25069的Datasheet PDF文件第1页浏览型号LM25069的Datasheet PDF文件第3页浏览型号LM25069的Datasheet PDF文件第4页浏览型号LM25069的Datasheet PDF文件第5页浏览型号LM25069的Datasheet PDF文件第6页浏览型号LM25069的Datasheet PDF文件第7页浏览型号LM25069的Datasheet PDF文件第8页浏览型号LM25069的Datasheet PDF文件第9页  
Connection Diagram  
30086702  
Top View  
10-Lead MSOP  
Ordering Information  
Order Number  
Fault Response  
Latch Off  
Package Type  
NSC Package  
Drawing  
Supplied As  
LM25069PMME-1  
LM25069PMM-1  
LM25069PMMX-1  
LM25069PMME-2  
LM25069PMM-2  
LM25069PMMX-2  
250 Units on Tape  
and Reel  
Latch Off  
1000 Units on  
Tape and Reel  
Latch Off  
3500 Units on  
Tape and Reel  
MSOP-10  
MUB10A  
Auto Restart  
Auto Restart  
Auto Restart  
250 Units on Tape  
and Reel  
1000 Units on  
Tape and Reel  
3500 Units on  
Tape and Reel  
Pin Descriptions  
Pin #  
Name  
Description  
Applications Information  
1
SENSE  
Current sense input  
The voltage across the current sense resistor (RS) is measured from VIN to this  
pin. If the voltage across RS reaches 50mV the load current is limited and the fault  
timer activates.  
2
3
VIN  
Positive supply input  
A small ceramic bypass capacitor close to this pin is recommended to suppress  
transients which occur when the load current is switched off.  
UVLO/EN Under-voltage lockout An external resistor divider from the system input voltage sets the under-voltage  
turn-on threshold. An internal 20 µA current source provides hysteresis. The  
enable threshold at the pin is 1.17V. This pin can also be used for remote  
shutdown control.  
4
OVLO  
Over-voltage lockout An external resistor divider from the system input voltage sets the over-voltage  
turn-off threshold. An internal 20 µA current source provides hysteresis. The  
disable threshold at the pin is 1.16V.  
5
6
GND  
Circuit ground  
TIMER  
Timing capacitor  
An external capacitor connected to this pin sets the insertion time delay and the  
Fault Timeout Period. The capacitor also sets the restart timing of the LM25069-2.  
7
8
PWR  
PGD  
Power limit set  
An external resistor connected to this pin, in conjunction with the current sense  
resistor (RS), sets the maximum power dissipation allowed in the external series  
pass MOSFET.  
Power Good indicator An open drain output. When the external MOSFET VDS decreases below 1.3V,  
the PGD indicator is active (high). When the external MOSFET VDS increases  
above 1.9V the PGD indicator switches low.  
www.national.com  
2
 复制成功!