Extended AC Electrical Characteristics
(SOIC package)
74ABT
74ABT
74ABT
e b
a
40 C to 85 C
e b a
40 C to 85 C
T
T
§
4.5V to 5.5V
§
§
4.5V to 5.5V
§
A
A
e b
a
40 C to 85 C
T
§
§
4.5V to 5.5V
A
e
e
V
V
CC
CC
e
V
CC
e
e
250 pF
Symbol
Parameter
C
50 pF
C
L
Units
L
e
C
250 pF
(Note 5)
L
8 Outputs Switching
(Note 4)
8 Outputs Switching
(Note 6)
Min
Max
Min
Max
Min
Max
t
t
Propagation Delay
1.5
1.5
5.2
5.2
2.0
2.0
6.8
6.8
2.0
2.0
9.0
9.0
PLH
ns
ns
ns
ns
D
n
to O
n
PHL
t
t
Propagation Delay
LE to O
1.5
1.5
5.5
5.5
2.0
2.0
7.5
7.5
2.0
2.0
9.5
9.5
PLH
PHL
n
t
t
Output Enable Time
1.5
1.5
6.2
6.2
2.0
2.0
8.0
8.0
2.0
2.0
10.5
10.5
PZH
PZL
t
t
Output Disable Time
1.0
1.0
5.5
5.5
PHZ
(Note 7)
(Note 7)
PZL
Note 4: This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH,
HIGH-to-LOW, etc.).
Note 5: This specification is guaranteed but not tested. The limits represent propagation delay with 250 pF load capacitors in plce of the 50 pF load capacitors in
the standard AC load. This specificaiton pertains to single output switching only.
Note 6: This specification is guaranteed but not tested. The limits represent propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH,
HIGH-to-LOW, etc.) with 250 pF load capacitors in place of the 50 pF load capacitors in the standard AC load.
Note 7: The TRI-STATE delay times are dominated by the RC network (500X, 250 pF) on the output and has been excluded from the datasheet.
Skew
74ABT
74ABT
e b
a
40 C to 85 C
e b
A
a
40 C to 85 C
T
T
§
4.5V–5.5V
§
§
4.5V–5.5V
§
A
e
e
V
CC
V
CC
C
Symbol
Parameter
e
e
250 pF
Units
C
50 pF
L
L
8 Outputs Switching
(Note 3)
8 Outputs Switching
(Note 4)
Max
Max
t
Pin to Pin Skew
HL Transitions
OSHL
(Note 1)
1.0
1.5
ns
ns
ns
ns
ns
t
Pin to Pin Skew
LH Transitions
OSLH
(Note 1)
1.0
1.4
1.5
2.0
1.5
3.5
3.9
4.0
t
Duty Cycle
PS
(Note 5)
LH–HL Skew
t
Pin to Pin Skew
OST
(Note 1)
LH/HL Transitions
t
Device to Device Skew
LH/HL Transitions
PV
(Note 2)
Note 1: Skew is defined as the absolute value of the difference between the actual propagation delays for any two separate outputs of the same device. The
specification applies to any outputs switching HIGH to LOW (t ), LOW to HIGH (t ), or any combination switching LOW to HIGH and/or HIGH to LOW
OSHL OSLH
(t
OST
). This specification is guaranteed but not tested.
Note 2: Propagation delay variation for a given set of conditions (i.e., temperature and V ) from device to device. This specification is guaranteed but not tested.
CC
Note 3: This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH,
HIGH-to-LOW, etc.).
Note 4: This specification is guaranteed but not tested. The limits represent propagation delays with 250 pF load capacitors in place of the 50 pF load capacitors in
the standard AC load.
Note 5: This describes the difference between the delay of the LOW-to-HIGH and the HIGH-to-LOW transition on the same pin. It is measured across all the
outputs (drivers) on the same chip, the worst (largest delta) number is the guaranteed specification. This specification is guaranteed but not tested.
5
NSC [ National Semiconductor ]
