欢迎访问ic37.com |
会员登录 免费注册
发布采购

GRM2195C1H682JA01D 参数 Datasheet PDF下载

GRM2195C1H682JA01D图片预览
型号: GRM2195C1H682JA01D
PDF下载: 下载PDF文件 查看货源
内容描述: 片状独石陶瓷电容器 [Chip Monolithic Ceramic Capacitors]
分类和应用: 电容器陶瓷电容器
文件页数/大小: 221 页 / 4341 K
品牌: MURATA [ muRata ]
 浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第69页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第70页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第71页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第72页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第74页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第75页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第76页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第77页  
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our  
C02E.pdf  
!Note  
sales representatives or product engineers before ordering.  
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.  
10.12.20  
GNM Series Specifications and Test Methods (1)  
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).  
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).  
Continued from the preceding page.  
Specifications  
No.  
Item  
Test Method  
Temperature  
Compensating Type  
High Dielectric Type  
Appearance No defects or abnormalities  
Capacitance Within the specified tolerance  
Solder the capacitor to the test jig (glass epoxy board) in the  
same manner and under the same conditions as (10). The  
capacitor should be subjected to a simple harmonic motion  
having a total amplitude of 1.5mm, the frequency being varied  
uniformly between the approximate limits of 10 and 55Hz. The  
frequency range, from 10 to 55Hz and return to 10Hz, should  
be traversed in approximately 1 minute. This motion should be  
applied for a period of 2 hours in each of 3 mutually perpendic-  
ular directions (total of 6 hours).  
30pF min.: QU1000  
Vibration  
Resistance  
11  
30pF max.:  
Char. 25V min. 16V  
R7, R6, 0.025 0.035 0.035 0.05  
10V  
6.3V  
QU400+20C  
Q/D.F.  
C7  
max.  
max.  
max.  
max.  
C: Nominal  
Capacitance (pF)  
Appearance No marking defects  
Solder the capacitor on the test jig (glass epoxy board) shown  
in Fig. 2 using a eutectic solder.  
Then apply a force in the direction shown in Fig. 3 for 5±1 sec.  
The soldering should be done by the reflow method and should  
be conducted with care so that the soldering is uniform and free  
of defects such as heat shock.  
Capacitance Within ±5% or ±0.5pF  
Within ±10%  
•GNMpp2  
Change  
(whichever is larger)  
•GNMpp4  
100  
5.0  
100  
5.0  
a
b
a
b
20  
12 Deflection  
Pressurizing  
speed: 1.0mm/sec.  
50  
c
1.0  
1.0  
Pressurize  
R230  
c
d
d
t=0.8mm  
Type  
a
b
c
d
Flexure : V1  
GNM1M2  
GNM212  
GNM214  
GNM314  
2.0±0.05 0.5±0.05 0.32±0.05 0.32±0.05  
2.0±0.05 0.6±0.05 0.5±0.05 0.5±0.05  
2.0±0.05 0.7±0.05 0.3±0.05 0.2±0.05  
2.5±0.05 0.8±0.05 0.4±0.05 0.4±0.05  
Capacitance meter  
45 45  
(in mm)  
Fig. 3  
Fig. 2  
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and  
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at  
80 to 120°C for 10 to 30 seconds. After preheating, immerse in  
eutectic solder solution for 2±0.5 seconds at 230±5°C or  
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.  
Solderability of  
Termination  
75% of the terminations are to be soldered evenly and  
continuously.  
13  
Resistance to  
Soldering Heat  
The measured and observed characteristics should satisfy the  
specifications in the following table.  
Appearance No marking defects  
Within ±2.5%  
or ±0.25pF  
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse  
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder  
solution at 270±5°C for 10±0.5 seconds. Let sit at room  
temperature for 24±2 hours, then measure.  
Capacitance  
R7, R6, C7: Within ±7.5%  
Change  
(whichever is  
larger)  
30pF min.: QU1000  
30pF max.:  
14  
• Initial measurement for high dielectric constant type  
Perform a heat treatment at 150+0/-10°C for one hour and  
then let sit for 24±2 hours at room temperature.  
Perform the initial measurement.  
Char. 25V min. 16V  
R7, R6, 0.025 0.035 0.035 0.05  
C7 max. max. max. max.  
10V  
6.3V  
QU400+20C  
Q/D.F.  
I.R.  
C: Nominal  
Capacitance (pF)  
More than 10,000Mor 500· F (whichever is smaller)  
Dielectric  
Strength  
No failure  
Continued on the following page.  
71