欢迎访问ic37.com |
会员登录 免费注册
发布采购

GRM2195C1H682JA01D 参数 Datasheet PDF下载

GRM2195C1H682JA01D图片预览
型号: GRM2195C1H682JA01D
PDF下载: 下载PDF文件 查看货源
内容描述: 片状独石陶瓷电容器 [Chip Monolithic Ceramic Capacitors]
分类和应用: 电容器陶瓷电容器
文件页数/大小: 221 页 / 4341 K
品牌: MURATA [ muRata ]
 浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第73页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第74页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第75页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第76页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第78页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第79页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第80页浏览型号GRM2195C1H682JA01D的Datasheet PDF文件第81页  
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our  
C02E.pdf  
!Note  
sales representatives or product engineers before ordering.  
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.  
10.12.20  
GNM Series Specifications and Test Methods (2)  
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).  
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).  
Continued from the preceding page.  
No.  
Item  
Specifications  
Test Method  
Appearance No marking defects  
Solder the capacitor to the test jig (glass epoxy board) shown in  
Fig. 2 using a eutectic solder. Then apply a force in the  
direction shown in Fig. 3. The soldering should be done by the  
reflow method and should be conducted with care so that the  
soldering is uniform and free of defects such as heat shock.  
Capacitance  
Change  
Within ±10%  
#GNMpp4  
#GNMpp2  
20  
Pressurizing  
50  
100  
1.0  
100  
1.0  
speed: 1.0mm/sec.  
Pressurize  
5.0  
a
b
5.0  
a
b
R230  
12 Deflection  
c
c
d
Thickness: 0.8mm  
d
Flexure : V1  
Type  
a
b
c
d
GNM0M2  
GNM1M2  
GNM212  
GNM214  
GNM314  
2.0±0.05 0.2±0.05 0.2±0.05 0.25±0.05  
2.0±0.05 0.5±0.05 0.32±0.05 0.32±0.05  
2.0±0.05 0.6±0.05 0.5±0.05 0.5±0.05  
2.0±0.05 0.7±0.05 0.3±0.05 0.2±0.05  
2.5±0.05 0.8±0.05 0.4±0.05 0.4±0.05  
Capacitance meter  
45 45  
Fig. 3  
(in mm)  
Fig. 2  
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and  
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at  
80 to 120°C for 10 to 30 seconds. After preheating, immerse in  
eutectic solder solution for 2±0.5 seconds at 230±5°C or  
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.  
Solderability of  
Termination  
75% of the terminations are to be soldered evenly  
and continuously.  
13  
Appearance No marking defects  
Capacitance R6*4: Within ±7.5%  
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse  
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder  
solution at 270±5°C for 10±0.5 seconds.  
Let sit at room temperature for 24±2 hours, then measure.  
• Initial measurement  
Perform a heat treatment at 150 +0/-10°C for one hour and  
then let sit for 24±2 hours at room temperature. Perform  
the initial measurement.  
Change  
*4 GNM0M2R60G105: Within +15/-7.5%  
Resistance  
0.1 max. *3  
*3 However 0.125 max. for Table 3 items.  
14 to Soldering D.F.  
Heat  
I.R.  
50· F min.  
Dielectric  
Strength  
No failure  
Appearance No marking defects  
R6*5: Within ±12.5%  
Fix the capacitor to the supporting jig in the same manner and  
under the same conditions as (10).  
Perform the five cycles according to the four heat treatments  
listed in the following table.  
*5 GNM0M2R60G105, GNM0M2R60J103/223/473/104,  
Capacitance  
Change  
GNM0M2R61A103/223/473/104,  
GNM0M2R61C103/223/473/104, GNM1M2R61A105:  
Let sit for 24±2 hours at room temperature, then measure.  
Step  
1
2
3
4
Within ±15%  
Temperature  
Cycle  
15  
Min. Operating Room Min. Operating Room  
Temp. (°C)  
Time (min.)  
0.1 max. *3  
Temp.  
Temp.  
Temp.  
Temp.  
D.F.  
I.R.  
*3 However 0.125 max. for Table 3 items.  
30±3  
2 to 3  
30±3  
2 to 3  
50· F min.  
• Initial measurement  
Perform a heat treatment at 150 +0/-10 °C for one hour and  
then let sit for 24±2 hours at room temperature.  
Perform the initial measurement.  
Dielectric  
Strength  
No failure  
Appearance No marking defects  
Apply the rated voltage at 40±2°C and 90 to 95% humidity for  
500±12 hours. The charge/discharge current is less than 50mA.  
• Initial measurement  
Perform a heat treatment at 150 +0/-10°C for one hour  
and then let sit for 24±2 hours at room temperature.  
Perform the initial measurement.  
Capacitance  
R6: Within ±12.5%  
Change  
High  
Temperature  
16 High  
Humidity  
D.F.  
I.R.  
0.2 max.  
• Measurement after test  
(Steady)  
Perform a heat treatment at 150 +0/-10°C for one hour  
and then let sit for 24±2 hours at room temperature, then  
measure.  
12.5· F min.  
Appearance No marking defects  
Apply 150% (GNM1M2R61A225/1C105: 125% of the rated  
voltage) of the rated voltage for 1000±12 hours at the  
maximum operating temperature ±3°C. Let sit for 24±2 hours  
at room temperature, then measure.  
Capacitance  
R6: Within ±12.5%  
Change  
D.F.  
I.R.  
0.2 max.  
The charge/discharge current is less than 50mA.  
• Initial measurement  
Perform a heat treatment at 150 +0/-10°C for one hour  
and then let sit for 24±2 hours at room temperature.  
Perform the initial measurement.  
17 Durability  
25· F min.  
• Measurement after test  
Perform a heat treatment at 150 +0/-10°C for one hour and  
then let sit for 24±2 hours at room temperature, then measure.  
75