• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and Test M thods (1) (Note 1)-Typical Inspection
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
(Note 1) These Specifications and Test Methods indicate typical inspection.
Please refer to individual specifications (our product specifications or the approval sheet).
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
Continued from the preceding page.
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
Specifications
No.
Item
Temperature
Compensating Type
Test Method
High Dielectric Type
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No defects or abnormalities
B1, B3, R1, R6, R7, C8:
Capacitance Within ±5% or ±0.5pF
Change
Within ±12.5%
(whichever is larger)
F1, F5, E4: Within ±30%
[R6, R7, C8]
W.V.: 100V
: 0.05 max. (CF0.068µF)
:
0.075 max. (CU0.068µF)
Set the capacitor at 40±2°C and in 90 to 95% humidity for
500±12 hours.
Remove and set for 24±2 hours at room temperature, then
measure.
Humidity
16 (Steady
State)
W.V.: 50/35/25/16/10V
: 0.05 max.
W.V.: 6.3/4V
: 0.075 max. (CF3.3µF)
: 0.125 max. (CU3.3µF)
[E4]
30pF and over: QU350
10pF and over
30pF and below:
QU275+2.5C
10pF and below:
QU200+10C
Q/D.F.
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
C: Nominal Capacitance (pF)
: 0.075 max. (CF0.1µF)
: 0.125 max. (CU0.1µF)
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
I.R.
More than 1,000MΩ or 50Ω · F (whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
No defects or abnormalities
B1, B3, R1, R6, R7, C8:
Within ±12.5%
F1, F5, E4: Within ±30%
[W.V.: 10V max.]
Capacitance Within ±7.5% or ±0.75pF
Change
(whichever is larger)
F1, F5: Within +30/–40%
[B1, B3, R6, R7, C8]
W.V.: 100V
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours. Remove and set for 24±2 hours at room
temperature, then measure.
: 0.05 max. (CF0.068µF)
:
0.075 max. (CU0.068µF)
The charge/discharge current is less than 50mA.
Humidity
Load
17
W.V.: 50/35/25/16/10V
: 0.05 max.
W.V.: 6.3/4V
: 0.075 max. (CF3.3µF)
: 0.125 max. (CU3.3µF)
[E4]
•Initial measurement for F1, F5/10V max.
Apply the rated DC voltage for 1 hour at 40±2°C.
Remove and set for 24±2 hours at room temperature.
Perform initial measurement.
30pF and over: QU200
30pF and below:
QU100+10C/3
Q/D.F.
C: Nominal Capacitance (pF)
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
: 0.075 max. (CF0.1µF)
: 0.125 max. (CU0.1µF)
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
I.R.
More than 500MΩ or 25Ω · F (whichever is smaller)
Continued on the following page.
55
MURATA [ muRata ]
