• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
AC250V(r.m.s.) Type (Which Meet Japanese Law) Specifications and Test Methods
GA2 Series Specifications and Test Methods
No.
1
Item
Operating
Specifications
Test Method
Y55 to W125D
Y
Temperature Range
2
3
Appearance
No defects or abnormalities
Visual inspection
Dimensions
Within the specified dimensions
Using calipers and micrometers
No failure should be observed when voltage in the table is
applied between the terminations for 60T1 sec., provided the
charge/discharge current is less than 50mA.
4
Dielectric Strength No defects or abnormalities
Nominal Capacitance
CU10,000pF
Test Voltage
AC575V (r.m.s.)
AC1500V (r.m.s.)
CF10,000pF
Insulation Resistance
More than 2,000MΩ
(I.R.)
The insulation resistance should be measured with DC500T50V
and within 60T5 sec. of charging.
5
6
7
Capacitance
Within the specified tolerance
0.025 max.
The capacitance/D.F. should be measured at a frequency of
1T0.2kHz and a voltage of AC1T0.2V (r.m.s.)
Dissipation
Factor (D.F.)
The capacitance measurement should be made at each step
specified in the Table.
Step
Temperature (D)
25T2
Min. Operating Temp.T3
25T2
Max. Operating Temp.T2
25T2
1
2
3
4
5
Capacitance
Temperature
Characteristics
Cap. Change
Within T15%
(Temp. Range: Y55 to W125D)
8
#Pretreatment
W 0
ꢀ
Perform a heat treatment at 150Y10D for 60T5 min. and then
let sit for 24T2 hrs. at room condition.*
As in Fig., discharge is made 50 times at 5 sec. intervals from
the capacitor (Cd) charged at DC voltage of specified.
R3
R1
Discharge
Test
(Application:
9
Appearance
No defects or abnormalities
R2
Ct
Nominal
10kV
V
Cd
Capacitance
CF10,000pF)
Ct: Capacitor under test Cd: 0.001µF
R1: 1,000Ω R2: 100MΩ R3: Surge resistance
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow. The soldering
should be done using the reflow method and should be
conducted with care so that the soldering is uniform and free of
defects such as heat shock.
Adhesive Strength
of Termination
10
No removal of the terminations or other defects should occur.
10N, 10T1s
Glass Epoxy Board
Fig. 1
Appearance
Capacitance
No defects or abnormalities
Within the specified tolerance
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
Vibration
Resistance
D.F.
11
0.025 max.
Solder resist
Cu
Glass Epoxy Board
* "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
188