PIC16F631/677/685/687/689/690
17.4 DC Characteristics: PIC16F631/677/685/687/689/690-I (Industrial)
PIC16F631/677/685/687/689/690-E (Extended)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
Conditions
VIL
Input Low Voltage
I/O Port:
with TTL buffer
D030
D030A
D031
D032
D033
D033A
Vss
Vss
Vss
VSS
VSS
VSS
—
—
—
—
—
—
0.8
V
V
V
V
V
V
4.5V ≤ VDD ≤ 5.5V
0.15 VDD
0.2 VDD
0.2 VDD
0.3
2.0V ≤ VDD ≤ 4.5V
2.0V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
(1)
MCLR, OSC1 (RC mode)
OSC1 (XT and LP modes)
OSC1 (HS mode)
Input High Voltage
I/O Ports:
0.3 VDD
VIH
—
—
—
—
—
—
—
—
D040
with TTL buffer
2.0
0.25 VDD + 0.8
0.8 VDD
0.8 VDD
1.6
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
4.5V ≤ VDD ≤ 5.5V
2.0V ≤ VDD ≤ 4.5V
2.0V ≤ VDD ≤ 5.5V
D040A
D041
with Schmitt Trigger buffer
MCLR
D042
D043
OSC1 (XT and LP modes)
OSC1 (HS mode)
D043A
D043B
0.7 VDD
0.9 VDD
OSC1 (RC mode)
(Note 1)
(2)
IIL
Input Leakage Current
D060
I/O ports
—
0.1
1
μA VSS ≤ VPIN ≤ VDD,
Pin at high-impedance
(3)
D061
D063
MCLR
—
—
0.1
0.1
5
5
μA VSS ≤ VPIN ≤ VDD
OSC1
μA VSS ≤ VPIN ≤ VDD, XT, HS and
LP oscillator configuration
D070* IPUR
VOL
PORTA Weak Pull-up Current
50
—
250
—
400
0.6
—
μA VDD = 5.0V, VPIN = VSS
(5)
Output Low Voltage
D080
I/O ports
V
V
IOL = 8.5 mA, VDD = 4.5V (Ind.)
IOH = -3.0 mA, VDD = 4.5V (Ind.)
(5)
VOH
Output High Voltage
D090
I/O ports
VDD – 0.7
—
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: See Section 10.2.1 “Using the Data EEPROM” for additional information.
5: Including OSC2 in CLKOUT mode.
DS41262D-page 234
© 2007 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
