PIC16C62X
12.4 DC CHARACTERISTICS: PIC16C62X/C62XA/CR62XA (Commercial, Industrial, Extended)
PIC16LC62X/LC62XA/LCR62XA (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
–40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial and
–40˚C ≤ TA ≤ +125˚C for extended
Operating voltage VDD range as described in DC spec Table 12-1 and Table 12-2
Param. Sym
No.
Characteristic
Min
Typ†
Max
Unit
Conditions
VIL
Input Low Voltage
I/O ports
with TTL buffer
D030
VSS
-
-
0.8V
V
VDD = 4.5V to 5.5V
otherwise
0.15VDD
0.2VDD
0.2VDD
D031
D032
with Schmitt Trigger input
MCLR, RA4/T0CKI,OSC1 (in RC
mode)
VSS
Vss
V
V
Note1
D033
OSC1 (in XT and HS)
OSC1 (in LP)
Vss
Vss
-
-
0.3VDD
V
V
0.6VDD-1.0
VIH Input High Voltage
I/O ports
-
-
D040
with TTL buffer
2.0V
.25VDD + 0.8V
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
VDD
VDD
V
VDD = 4.5V to 5.5V
otherwise
D041
D042
D043
D043A
D070
with Schmitt Trigger input
VDD
VDD
VDD
MCLR RA4/T0CKI
OSC1 (XT, HS and LP)
OSC1 (in RC mode)
-
-
V
V
Note1
IPURB PORTB weak pull-up current
Input Leakage Current
200
400
µA VDD = 5.0V, VPIN = VSS
IIL
(Notes 2, 3)
I/O ports (Except PORTA)
PORTA
±1.0
±0.5
±1.0
±5.0
µA VSS ≤ VPIN ≤ VDD, pin at hi-impedance
µA Vss ≤ VPIN ≤ VDD, pin at hi-impedance
µA Vss ≤ VPIN ≤ VDD
D060
D061
D063
-
-
-
-
-
-
RA4/T0CKI
OSC1, MCLR
µA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
configuration
VOL Output Low Voltage
D080
D083
I/O ports
-
-
-
-
-
-
-
-
0.6
0.6
0.6
0.6
V
V
V
V
IOL=8.5 mA, VDD=4.5V, -40° to +85°C
IOL=7.0 mA, VDD=4.5V, +125°C
IOL=1.6 mA, VDD=4.5V, -40° to +85°C
IOL=1.2 mA, VDD=4.5V, +125°C
OSC2/CLKOUT (RC only)
VOH Output High Voltage (Note 3)
D090
D092
*
I/O ports (Except RA4)
VDD-0.7
VDD-0.7
VDD-0.7
VDD-0.7
-
-
-
-
-
-
V
V
V
V
V
IOH=-3.0 mA, VDD=4.5V, -40° to +85°C
IOH=-2.5 mA, VDD=4.5V, +125°C
IOH=-1.3 mA, VDD=4.5V, -40° to +85°C
IOH=-1.0 mA, VDD=4.5V, +125°C
RA4 pin PIC16C62X, PIC16LC62X
RA4 pin PIC16C62XA, PICLC62XA,
CR62XA, LCR62XA
OSC2/CLKOUT (RC only)
-
-
Open-Drain High Voltage
10*
10*
VOD
Capacitive Loading Specs on
Output Pins
D100
COSC2 OSC2 pin
15
50
pF In XT, HS and LP modes when external
clock used to drive OSC1.
pF
D101
Cio All I/O pins/OSC2 (in RC mode)
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. It is not recommended that the PIC16C62X(A) be driven
with external clock in RC mode.
Note 1:
2: The leakage current on the MCLR pin is strongly dependent on applied voltage level. The specified levels represent normal operat-
ing conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as coming out of the pin.
DS30235G-page 84
Preliminary
1998 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
