欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC16F777-I/PT 参数 Datasheet PDF下载

PIC16F777-I/PT图片预览
型号: PIC16F777-I/PT
PDF下载: 下载PDF文件 查看货源
内容描述: 28 /40/ 44引脚, 8位CMOS闪存微控制器与10位A / D和纳瓦技术 [28/40/44-Pin, 8-Bit CMOS Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology]
分类和应用: 闪存微控制器
文件页数/大小: 276 页 / 4898 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC16F777-I/PT的Datasheet PDF文件第101页浏览型号PIC16F777-I/PT的Datasheet PDF文件第102页浏览型号PIC16F777-I/PT的Datasheet PDF文件第103页浏览型号PIC16F777-I/PT的Datasheet PDF文件第104页浏览型号PIC16F777-I/PT的Datasheet PDF文件第106页浏览型号PIC16F777-I/PT的Datasheet PDF文件第107页浏览型号PIC16F777-I/PT的Datasheet PDF文件第108页浏览型号PIC16F777-I/PT的Datasheet PDF文件第109页  
PIC16F7X7  
REGISTER 10-3: SSPSTAT: MSSP STATUS (I2C MODE) REGISTER (ADDRESS 94h)  
R/W-0  
SMP  
R/W-0  
CKE  
R-0  
D/A  
R-0  
P
R-0  
S
R-0  
R-0  
UA  
R-0  
BF  
R/W  
bit 7  
bit 0  
bit 7  
bit 6  
bit 5  
SMP: Slew Rate Control bit  
In Master or Slave mode:  
1= Slew rate control disabled for Standard Speed mode (100 kHz and 1 MHz)  
0= Slew rate control enabled for High-Speed mode (400 kHz)  
CKE: SMBus Select bit  
In Master or Slave mode:  
1= Enable SMBus specific inputs  
0= Disable SMBus specific inputs  
D/A: Data/Address bit  
In Master mode:  
Reserved.  
In Slave mode:  
1= Indicates that the last byte received or transmitted was data  
0= Indicates that the last byte received or transmitted was address  
bit 4  
bit 3  
bit 2  
P: Stop bit  
1= Indicates that a Stop bit has been detected last  
0= Stop bit was not detected last  
Note:  
This bit is cleared on Reset and when SSPEN is cleared.  
S: Start bit  
1= Indicates that a Start bit has been detected last  
0= Start bit was not detected last  
Note:  
This bit is cleared on Reset and when SSPEN is cleared.  
R/W: Read/Write bit Information bit (I2C mode only)  
In Slave mode:  
1= Read  
0= Write  
Note:  
This bit holds the R/W bit information following the last address match. This bit is  
only valid from the address match to the next Start bit, Stop bit or not ACK bit.  
In Master mode:  
1= Transmit is in progress  
0= Transmit is not in progress  
Note:  
ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is  
in Idle mode.  
bit 1  
bit 0  
UA: Update Address bit (10-bit Slave mode only)  
1= Indicates that the user needs to update the address in the SSPADD register  
0= Address does not need to be updated  
BF: Buffer Full Status bit  
In Transmit mode:  
1= Receive complete, SSPBUF is full  
0= Receive not complete, SSPBUF is empty  
In Receive mode:  
1= Data transmit in progress (does not include the ACK and Stop bits), SSPBUF is full  
0= Data transmit complete (does not include the ACK and Stop bits), SSPBUF is empty  
Legend:  
R = Readable bit  
-n = Value at POR  
W = Writable bit  
‘1’ = Bit is set  
U = Unimplemented bit, read as ‘0’  
‘0’ = Bit is cleared x = Bit is unknown  
2004 Microchip Technology Inc.  
DS30498C-page 103  
 复制成功!