欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC10F200-I/P 参数 Datasheet PDF下载

PIC10F200-I/P图片预览
型号: PIC10F200-I/P
PDF下载: 下载PDF文件 查看货源
内容描述: 6引脚8位闪存微控制器 [6-Pin, 8-Bit Flash Microcontrollers]
分类和应用: 闪存微控制器和处理器外围集成电路光电二极管PC时钟
文件页数/大小: 96 页 / 1447 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC10F200-I/P的Datasheet PDF文件第64页浏览型号PIC10F200-I/P的Datasheet PDF文件第65页浏览型号PIC10F200-I/P的Datasheet PDF文件第66页浏览型号PIC10F200-I/P的Datasheet PDF文件第67页浏览型号PIC10F200-I/P的Datasheet PDF文件第69页浏览型号PIC10F200-I/P的Datasheet PDF文件第70页浏览型号PIC10F200-I/P的Datasheet PDF文件第71页浏览型号PIC10F200-I/P的Datasheet PDF文件第72页  
PIC10F200/202/204/206  
12.2 DC Characteristics: PIC10F200/202/204/206 (Extended)  
Standard Operating Conditions (unless otherwise specified)  
Operating Temperature -40×C £ TA £ +125×C (extended)  
DC CHARACTERISTICS  
Param  
Sym  
No.  
(1)  
Characteristic  
Supply Voltage  
Min  
Typ  
Max  
Units  
Conditions  
D001  
D002  
D003  
VDD  
VDR  
2.0  
1.5*  
5.5  
V
V
V
See Figure 12-1  
(2)  
RAM Data Retention Voltage  
Device in Sleep mode  
VPOR  
VDD Start Voltage  
Vss  
to ensure Power-on Reset  
D004  
D010  
D020  
D022  
D023  
D024  
SVDD  
IDD  
VDD Rise Rate  
to ensure Power-on Reset  
0.05*  
V/ms  
(3)  
Supply Current  
175  
0.63  
275  
1.1  
μA  
mA  
VDD = 2.0V  
VDD = 5.0V  
(4)  
IPD  
Power-down Current  
0.1  
0.35  
9
15  
μA  
μA  
VDD = 2.0V  
VDD = 5.0V  
(5)  
IWDT  
ICMP  
VREF  
WDT Current  
1.0  
7
18  
22  
μA  
μA  
VDD = 2.0V  
VDD = 5.0V  
(5)  
Comparator Current  
12  
42  
27  
85  
μA  
μA  
VDD = 2.0V  
VDD = 5.0  
(5), (6)  
Internal Reference Current  
85  
175  
120  
200  
μA  
μA  
VDD = 2.0V  
VDD = 5.0V  
*
These parameters are characterized but not tested.  
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only  
and is not tested.  
2: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.  
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, bus  
rate, internal code execution pattern and temperature also have an impact on the current consumption.  
a) The test conditions for all IDD measurements in active operation mode are:  
All I/O pins tri-stated, pulled to VSS, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.  
b) For standby current measurements, the conditions are the same, except that the device is in Sleep mode.  
4: Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD  
or VSS.  
5: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is  
enabled.  
6: Measured with the Comparator enabled.  
DS41239D-page 66  
© 2007 Microchip Technology Inc.  
 复制成功!