MV78100
Hardware Specifications
9.7.3
SATA Interface Electrical Characteristics
9.7.3.1
SATA I Interface Gen1 Mode Driver and Receiver Characteristics
Table 54: SATA I Interface Gen1i Mode Driver and Receiver Characteristicss
Description
Symbol
BR
Min
Max
Units
Gbps
ppm
kHz
Notes
Baud Rate
1.5
-
-
-
-
-
Baud rate tolerance
Bppm
Fssc
SSCtol
UI
-350.0
30.0
350.0
33.0
0.0
Spread spectrum modulation frequency
Spread spectrum modulation Deviation
Unit Interval
-5000.0
ppm
ps
666.67
Driver Parameters
Differential impedance
Zdifftx
Zsetx
RLOD
RLOD
RLOD
RLOD
RLOD
Vdifftx
TJ5
85.0
40.0
14.0
8.0
6.0
3.0
1.0
400.0
-
115.0
Ohm
Ohm
dB
dB
dB
dB
dB
mV
UI
-
-
Single ended impedance
-
Differential return loss (75 MHz-150 MHz)
Differential return loss (150 MHz-300 MHz)
Differential return loss (300 MHz-1.2 GHz)
Differential return loss (1.2 GHz-2.4 GHz)
Differential return loss (2.4 GHz-3.0 GHz)
Output differential voltage
-
-
-
-
-
-
-
-
-
-
600.0
0.355
0.175
0.470
0.220
2
1
-
Total jitter at connector data-data, 5UI
Deterministic jitter at connector data-data, 5UI
Total jitter at connector data-data, 250UI
Deterministic jitter at connector data-data, 250UI
DJ5
-
UI
TJ250
DJ250
-
UI
1
-
-
UI
Receiver Parameters
Differential impedance
Zdiffrx
Zsetx
RLID
RLID
RLID
RLID
RLID
RLID
Vdiffrx
TJ5
85.0
40.0
18.0
14.0
10.0
8.0
3.0
1.0
325.0
-
115.0
Ohm
Ohm
dB
dB
dB
dB
dB
dB
mV
UI
-
-
Single ended impedance
-
Differential return loss (75 MHz-150 MHz)
Differential return loss (150 MHz-300 MHz)
Differential return loss (300 MHz-600 MHz)
Differential return loss (600 MHz-1.2 GHz)
Differential return loss (1.2 GHz-2.4 GHz)
Differential return loss (2.4 GHz-3.0 GHz)
Input differential voltage
-
-
-
-
-
-
-
-
-
-
-
-
600.0
0.430
0.250
0.600
0.350
-
Total jitter at connector data-data, 5UI
Deterministic jitter at connector data-data, 5UI
Total jitter at connector data-data, 250UI
Deterministic jitter at connector data-data, 250UI
1
-
DJ5
-
UI
TJ250
DJ250
-
UI
1
-
-
UI
Notes :
General Comment: For more information, refer to SATA II Revision 2.6 Specification, February, 2007.
General Comment: The load is 100 ohm differential for these parameters, unless otherw ise specified.
General Comment: To comply w ith the values presented in this table, refer to your local
Marvell representative for register settings.
1. Total jitter is defined as TJ = (14 * RJσ) + DJ w here Rjσ is random jitter.
2. Output Differential Amplitude and Pre-Emphasis are configurabile. See functional register description
for more details.
MV-S104552-U0 Rev. D
Copyright © 2008 Marvell
Page 108
Document Classification: Proprietary Information
December 6, 2008, Preliminary