MACH131 AND MACH131SP
SWITCHING CHARACTERISTICS OVER OPERATING RANGES1
-5
-7
-10
-12
-14
-15
-18
Parameter
Symbol
Parameter Description
Min Max Min Max Min Max Min Max Min Max Min Max Min Max Unit
t
Input, I/O, or Feedback to Combinatorial Output
5.5
7.5
10
12
14
10
15
10
18 ns
PD
D-type
Setup Time from Input, I/O, or Feedback
T-type
3.0
3.5
0
5.5
6.5
0
6.5
7.5
0
7
8
0
8.5
10
0
10
11
0
12
13.5
0
ns
t
S
ns
ns
t
Hold Time
H
t
Clock to Output
4
5
6
8
12 ns
ns
CO
t
LOW
2.5
2.5
3
3
4
4
6
6
6
7.5
7.5
42
39
53
44
WL
Clock Width
HIGH
t
6
6
6
ns
WH
D-type
143
133
182
167
95
87
133
125
80
74
100
91
66.7
62.5
76.9
71.4
54
50
69
57
50
MHz
External
Feedback
1/(t + t )
S
CO
T-type
D-type
T-type
47.6
66.6
55.5
MHz
MHz
MHz
Maximum
Frequency
f
MAX
Internal Feedback (f
)
CNT
No
Feedback
1/(t + t
)
200
167
125
83.3
83.3
83.3
66.7
MHz
WL WH
t
Asynchronous Reset to Registered Output
Asynchronous Reset Width (Note 2)
8.5
8.5
9.5
9.5
11
11
16
16
19.5
19.5
20
20
24 ns
AR
t
4.5
4.5
5
5
7.5
7.5
12
8
14.5
10
15
10
18
12
ns
ns
ARW
t
Asynchronous Reset Recovery Time (Note 2)
Asynchronous Preset to Registered Output
Asynchronous Preset Width (Note 2)
ARR
t
24 ns
ns
AP
t
4.5
4.5
5
5
7.5
7.5
12
8
14.5
10
15
10
18
12
APW
t
Asynchronous Preset Recovery Time (Note 2)
Input, I/O, or Feedback to Output Enable
Input, I/O, or Feedback to Output Disable
ns
APR
t
7.5
7.5
10
7
9.5
9.5
10
7
10
10
10
7
12
12
10
7
14.5
14.5
10
7
15
15
10
7
18 ns
18 ns
10 ns
EA
t
ER
t
t Increase for Powered-Down Macrocell (Note 3)
PD
LP
t
t Increase for Powered-Down Macrocell (Note 3)
7
3
ns
ns
LPS
S
t
t
Increase for Powered-Down Macrocell (Note 3)
Increase for Powered-Down Macrocell (Note 3)
EA
3
3
3
3
3
3
LPCO
CO
t
t
10
10
10
10
10
10
10 ns
LPEA
Notes:
1. See “Switching Test Circuit” in the General Information Section of the Vantis 1999 Data Book..
2. These parameters are not 100% tested, but are evaluated at initial characterization and at any time the design is modified where
this parameter may be affected.
3. If a signal is powered down, this parameter must be added to its respective high-speed parameter.
26
MACH 1 & 2 Families