Interꢀchannel
25 | Keysight | Infiniium 90000 Series Oscilloscopes - Data Sheet
Infiniium 90000A Series Oscilloscopes (Continued)
Performance characteristics (Continued)
Vertical (Continued)
RMS noise floor (scope with probe)
Volts/div
90254A with
1131A
90404A with 90604A with
90804A with 91204A with
91304A with
1169A
2.7 mV
3.1 mV
4.2 mV
7.5 mV
19 mV
1132A
3.5 mV
3.6 mV
3.8 mV
4.6 mV
8.6 mV
16 mV
1134A
4.0 mV
4.0 mV
4.3 mV
5.3 mV
10 mV
19 mV
1168A
2.2 mV
2.3 mV
2.9 mV
4.7 mV
12 mV
23 mV
1169A
2.5 mV
2.8 mV
3.5 mV
5.9 mV
15 mV
28 mV
20 mV
50 mV
100 mV
200 mV
500 mV
1 V
3.2 mV
3.3 mV
3.4 mV
4.0 mV
7.1 mV
13 mV
37 mV
Horizontal
Main timebase range
Main timebase delay range
Zoom timebase range
Time scale accuracy 1, 8
Oscilloscope channel de-skew range
Intrinsic jitter 6 (sample clock jitter)
5 ps/div to 200 s/div real-time
–200 s to 200 s real-time
1 ps/div to current main time scale setting
± (0.4 ppm initial + 0.5 ppm/year aging)
± 25 µs range, 100 fs resolution
Acquired time range or delta-time
delta-time Interval
< 100 µs (10 µs/div)
1 ms (100 µs/div)
10 ms (1 ms/div)
100 ms (10 ms/div)
550 fs rms
Internal reference
0.5 ps rms
1.0 ps rms
1.2 ps rms
5.0 ps rms
External reference
0.5 ps rms
1.0 ps rms
1.2 ps rms
1.2 ps rms
Inter-channel intrinsic jitter 3
Inter-channel skew drift 3, 7
Jitter measurement floor 2
Time interval error
< 500 fs rms
2
NoiseꢀFloor
SlewꢀRate
+ Intrinsic Jitterꢀ 2
(
)
Period jitter
2
NoiseꢀFloor
SlewꢀRate
2
2i
3i
+ IntrinsicꢀJitter
(
)
Cycle-cycle/N-cycle jitter
Inter-channel jitter measurement floor 2, 3, 5
2
NoiseꢀFloor
SlewꢀRate
2
2
+ IntrinsicꢀJitter
(
)
2
2
TimeꢀIntervalꢀ
TimeꢀIntervalꢀ
Error Edge2
+
+
Error Edge1
IntrinsicꢀJitter
(
)
(
)
1� Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 5 °C from firmware calibration
temperature�
2� Sample rate at maximum� Noise and slew rate determined at fixed-voltage measurement threshold, near middle of signal� Displayed signal not vertically
clipped. Slew rate of sine wave = (peak signal amplitude) • 2 • π • f, slew rate of fast step ~= (10 to 90% rise time).
3� Intra-channel = both edges on the same channel, inter-channel = two edges on different channels� Time Interval Error(Edge1) = time-interval error
measurement floor of first edge, time interval error(Edge2) = time-interval error measurement floor of second edge�
4� Reading is the displayed delta time measurement accuracy measurement value� Do not double the listed time scale accuracy value in delta time
measurement accuracy formula�
5� Scope channels and signal interconnect de-skewed prior to measurement�
6� External timebase reference values measured using a Wenzel 501-04608A 10 MHz reference� Intrinsic jitter value depends on acquisition time range for
Time Interval Error formula and depends on delta-time between edges for all two-edge formulas�
7� Skew between channels caused by ± 5 ºC temperature change.
8� Initial = immediately after factory or user calibration�