欢迎访问ic37.com |
会员登录 免费注册
发布采购

X5083V8I-2.7 参数 Datasheet PDF下载

X5083V8I-2.7图片预览
型号: X5083V8I-2.7
PDF下载: 下载PDF文件 查看货源
内容描述: CPU监控与9Kbit SPI EEPROM [CPU Supervisor with 9Kbit SPI EEPROM]
分类和应用: 光电二极管监控可编程只读存储器电动程控只读存储器电可擦编程只读存储器
文件页数/大小: 20 页 / 348 K
品牌: INTERSIL [ Intersil ]
 浏览型号X5083V8I-2.7的Datasheet PDF文件第9页浏览型号X5083V8I-2.7的Datasheet PDF文件第10页浏览型号X5083V8I-2.7的Datasheet PDF文件第11页浏览型号X5083V8I-2.7的Datasheet PDF文件第12页浏览型号X5083V8I-2.7的Datasheet PDF文件第14页浏览型号X5083V8I-2.7的Datasheet PDF文件第15页浏览型号X5083V8I-2.7的Datasheet PDF文件第16页浏览型号X5083V8I-2.7的Datasheet PDF文件第17页  
X5083  
Absolute Maximum Ratings  
Operating Conditions  
Temperature Range  
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . .-65°C to 135°C  
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to 150°C  
Voltage on Any Pin with Respect To Vss . . . . . . . . . . . . . -1.0V to 7V  
D.C. Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA  
Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . .300°C  
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C  
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C  
V
CC Range  
-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V  
Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V  
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the  
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.  
DC Electrical Specifications (Over the recommended operating conditions unless otherwise specified.)  
LIMITS  
SYMBOL  
PARAMETER  
TEST CONDITIONS  
MIN  
TYP  
MAX  
UNIT  
ICC1  
VCC Write Current (Active)  
SCK = VCC x 0.1/VCC x 0.9 @ 5MHz,  
SO = Open  
5
mA  
ICC2  
ISB1  
ISB2  
ISB3  
VCC Read Current (Active)  
SCK = VCC x 0.1/VCC x 0.9 @ 5MHz,  
SO = Open  
0.4  
1
mA  
µA  
µA  
µA  
VCC Standby Current WDT = OFF CS = VCC, VIN = VSS or VCC  
VCC = 5.5V  
,
,
,
VCC Standby Current WDT = ON CS = VCC, VIN = VSS or VCC  
VCC = 5.5V  
50  
20  
VCC Standby Current WDT = ON CS = VCC, VIN = VSS or VCC  
V
CC = 3.6V  
ILI  
Input Leakage Current  
Output Leakage Current  
VIN = VSS to VCC  
0.1  
0.1  
10  
10  
µA  
µA  
V
ILO  
VOUT = VSS to VCC  
V
IL (Note 1) Input LOW Voltage  
-0.5  
VCC x 0.3  
VCC + 0.5  
0.4  
V
IH (Note 1) Input HIGH Voltage  
VCC x 0.7  
V
VOL1  
VOL2  
VOL3  
VOH1  
VOH2  
VOH3  
VOLRS  
Output LOW Voltage  
Output LOW Voltage  
Output LOW Voltage  
Output HIGH Voltage  
Output HIGH Voltage  
Output HIGH Voltage  
Reset Output LOW Voltage  
VCC > 3.3V, IOL = 2.1mA  
V
2V < VCC 3.3V, IOL = 1mA  
0.4  
V
V
CC 2V, IOL = 0.5mA  
VCC > 3.3V, IOH = -1.0mA  
2V < VCC 3.3V, IOH = -0.4mA  
CC 2V, IOH = -0.25mA  
IOL = 1mA  
0.4  
V
VCC - 0.8  
VCC - 0.4  
VCC - 0.2  
V
V
V
V
0.4  
V
Power-Up Timing  
SYMBOL  
PARAMETER  
MIN  
MAX  
UNIT  
tPUR (Note 2) Power-up to read operation  
PUW (Note 2) Power-up to write operation  
1
5
ms  
ms  
t
.
Capacitance TA = +25°C, f = 1MHz, VCC = 5V  
SYMBOL TEST  
OUT (Note 2) Output capacitance (SO, RESET, RESET)  
IN (Note 2) Input capacitance (SCK, SI, CS, WP)  
MAX  
UNIT  
pF  
CONDITIONS  
VOUT = 0V  
VIN = 0V  
C
8
6
C
pF  
NOTES:  
1. VIL min. and VIH max. are for reference only and are not tested.  
2. This parameter is periodically sampled and not 100% tested.  
FN8127.2  
September 16, 2005  
13