欢迎访问ic37.com |
会员登录 免费注册
发布采购

HIP6601BCB-T 参数 Datasheet PDF下载

HIP6601BCB-T图片预览
型号: HIP6601BCB-T
PDF下载: 下载PDF文件 查看货源
内容描述: 同步整流降压MOSFET驱动器 [Synchronous Rectified Buck MOSFET Drivers]
分类和应用: 驱动器接口集成电路光电二极管
文件页数/大小: 11 页 / 344 K
品牌: INTERSIL [ Intersil ]
 浏览型号HIP6601BCB-T的Datasheet PDF文件第3页浏览型号HIP6601BCB-T的Datasheet PDF文件第4页浏览型号HIP6601BCB-T的Datasheet PDF文件第5页浏览型号HIP6601BCB-T的Datasheet PDF文件第6页浏览型号HIP6601BCB-T的Datasheet PDF文件第7页浏览型号HIP6601BCB-T的Datasheet PDF文件第8页浏览型号HIP6601BCB-T的Datasheet PDF文件第9页浏览型号HIP6601BCB-T的Datasheet PDF文件第11页  
HIP6601B, HIP6603B, HIP6604B  
Quad Flat No-Lead Plas tic Package (QFN)  
L16.4x4  
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE  
(COMPLIANT TO JEDEC MO-220-VGGC ISSUE C)  
Micro Lead Frame Plas tic Package (MLFP)  
MILLIMETERS  
SYMBOL  
MIN  
NOMINAL  
MAX  
1.00  
0.05  
1.00  
NOTES  
A
A1  
A2  
A3  
b
0.80  
0.90  
-
-
-
-
-
-
9
0.20 REF  
9
0.23  
1.95  
1.95  
0.28  
0.35  
2.25  
2.25  
5, 8  
D
4.00 BSC  
-
D1  
D2  
E
3.75 BSC  
9
2.10  
7, 8  
4.00 BSC  
-
E1  
E2  
e
3.75 BSC  
9
2.10  
7, 8  
0.65 BSC  
-
k
0.25  
0.50  
-
-
-
-
L
0.60  
0.75  
0.15  
8
L1  
N
-
16  
4
4
-
10  
2
Nd  
Ne  
P
3
3
-
-
0.60  
12  
9
θ
-
9
Rev. 5 5/04  
NOTES:  
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.  
2. N is the number of terminals.  
3. Nd and Ne refer to the number of terminals on each D and E.  
4. All dimensions are in millimeters. Angles are in degrees.  
5. Dimension b applies to the metallized terminal and is measured  
between 0.15mm and 0.30mm from the terminal tip.  
6. The configuration of the pin #1 identifier is optional, but must be  
located within the zone indicated. The pin #1 identifier may be  
either a mold or mark feature.  
7. Dimensions D2 and E2 are for the exposed pads which provide  
improved electrical and thermal performance.  
8. Nominal dimensionsare provided toassistwith PCBLandPattern  
Design efforts, see Intersil Technical Brief TB389.  
9. Features and dimensions A2, A3, D1, E1, P & θ are present when  
Anvil singulation method is used and not present for saw  
singulation.  
10. Depending on the method of lead termination at the edge of the  
package, a maximum 0.15mm pull back (L1) maybe present. L  
minus L1 to be equal to or greater than 0.3mm.  
FN9072.7  
10  
July 20, 2005