DG411, DG412, DG413
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Thermal Resistance (Typical, Note 2)
θ
(°C/W)
JA
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Packages). . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
90
110
150
V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) to (V+) +0.3V
L
Digital Inputs, V , V (Note 1). . . . . (V-) -2V to (V+) + 2V or 30mA,
S
D
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
(SOIC and TSSOP - Lead Tips Only)
Operating Conditions
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. Signals on S , D , or IN exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
X
X
X
2. θ is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, V = 5V, V = 2.4V, 0.8V (Note 3),
L
IN
Unless Otherwise Specified.
TEMP
(°C)
MIN
(Note 4)
TYP
(Note 5)
MAX
(Note 4) UNITS
PARAMETER
TEST CONDITIONS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
R
= 300Ω, C = 35pF, V = ±10V (Figure 1)
25
85
25
85
25
25
25
25
-
-
-
-
-
-
-
-
110
-
175
ns
ns
ns
ns
ns
pC
dB
dB
ON
L
L
S
220
Turn-OFF Time, t
100
-
145
OFF
160
Break-Before-Make Time Delay
Charge Injection, Q (Figure 3)
OFF Isolation (Figure 5)
DG413 Only, R = 300Ω, C = 35pF (Figure 2)
25
5
-
-
-
-
L
L
C
R
= 10nF, V = 0V, R = 0Ω
G G
L
L
= 50Ω, C = 5pF, f = 1MHz
68
-85
L
Crosstalk (Channel-to-Channel),
(Figure 4)
Source OFF Capacitance, C
f = 1MHz (Figure 6)
25
25
25
-
-
-
9
9
-
-
-
pF
pF
pF
S(OFF)
Drain OFF Capacitance, C
Channel ON Capacitance,
D(OFF)
35
C
+ C
D(ON)
S(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current V Low, I
V
V
Under Test = 0.8V, All Others = 2.4V
Under Test = 2.4V, All Others = 0.8V
Full
Full
-0.5
-0.5
0.005
0.005
0.5
0.5
μA
μA
IN IL
IN
IN
Input Current V High, I
IN IH
ANALOG SWITCH CHARACTERISTICS
±
Analog Signal Range, V
ANALOG
I
I
=
=
10mA
Full
25
-15
-
25
-
15
35
45
V
Ω
Ω
S
S
±
Drain-Source ON Resistance,
10mA, V = ±8.5V, V+ = 13.5V, V- = -13.5V
-
-
D
r
DS(ON)
Full
FN3282.13
June 20, 2007
4
INTERSIL [ Intersil ]
