.
IBM16M64734BGA
Preliminary
Features
• 184-Pin Registered 8-Byte Dual In-Line Memory
Module
• 64Mx72 Double Data Rate (DDR) SDRAM
DIMM (64M
X
4 SDRAM
S
)
• Performance:
DIMM CAS Latency
f
CK
t
CK
f
DQ
Clock Frequency
Clock Cycle
DQ Burst Frequency
PC200
3
3.5
100
10
200
125
8.0
250
PC266B
3
3.5
125
8.0
250
133
7.5
266
Units
MHz
ns
MHz
64Mx72 1 Bank Registered DDR SDRAM Module
• Bi-directional data strobe with one clock cycle
preamble and one-half clock post-amble
• Differential clock inputs
• Data is read or written on both clock edges
• Address and control signals are fully synchro-
nous to positive clock edge
• Programmable Operation:
- DIMM CAS Latency: 3, 3.5
- Burst Type: Sequential or Interleave
- Burst Length: 2, 4, 8
- Operation: Burst Read and Write
• Auto Refresh (CBR) and Self Refresh Modes
• Automatic and controlled precharge commands
• Power Down Mode
• 13/11/2 Addressing (row/column/bank)
• 7.8
µs
Max. Average Periodic Refresh Interval
• Card size: 5.25" x 0.157" x 1.70"
• Gold contacts
• SDRAM
S
in 66-pin TSOP-II Package
•
•
•
•
•
Intended for 100MHz and 133MHz applications
Inputs and outputs are SSTL-2 compatible
V
DD
= 2.5Volt
±
0.2, V
DDQ
= 2.5Volt
±
0.2
Single Pulsed RAS interface
SDRAMs have four internal banks for concur-
rent operation
• Module has one physical bank
• Serial Presence Detect
Description
This Registered 184-Pin Double Data Rate (DDR)
Synchronous DRAM Dual In-Line Memory Module
(DIMM) is organized as a one-bank high-speed
memory array. The 64Mx72 is a single-bank DIMM
that uses eighteen 64Mx4 DDR SDRAMs in 400 mil
TSOP packages. This DIMM achieves high-speed
data transfer rates of up to 266MHz.
The DIMM is intended for use in applications oper-
ating from 100MHz to 133MHz clock speeds with
data rates of 200 to 266 MHz. All control and
address signals are re-driven through registers to
the DDR SDRAM devices. The control and address
input signals are latched in the register on one rising
clock edge and sent to the SDRAM devices on the
following rising clock edge.
A phase-locked loop (PLL) on the DIMM is used to
re-drive the differential clock signals to both the
DDR SDRAM devices and the registers, thus mini-
mizing system clock loading. Clock enable (CKE0)
controls all devices on the DIMM.
Prior to any access operation, the device CAS
latency and burst type/length/operation type must
be programmed into the DIMM by address inputs
A0-A12 using the mode register set cycle. The
DIMM CAS latency exceeds the SDRAM device
spec by one clock due to the address and control
signals being clocked to the SDRAM devices.
These DIMMs are manufactured using raw cards
developed for broad industry use by IBM as ’refer-
ence designs’. The use of these common design
files will minimize electrical variation between sup-
pliers.
The DIMM uses serial presence detects imple-
mented via a serial EEPROM using the two-pin IIC
protocol. The first 128 bytes of serial PD data are
programmed and locked during module assembly.
The last 128 bytes are available to the customer.
All IBM 184 DDR SDRAM DIMMs provide a high-
performance, flexible 8-byte interface in a 5.25” long
space-saving footprint.
06K6597.H02812
3/00
©IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 1 of 23
IBM [ IBM ]
